Skip to content
S.B. Electronics Printed circuit boards · since 2000, home page

Industries · Automotive & EV

Automotive and EV PCB manufacturer in India

Boards for EV chargers, battery management, lighting and body electronics, built on high-Tg FR-4 with the copper, hole plating and test a vehicle programme asks for. IPC Class 3 on request; your own quality requirements go on the drawing.

HV DC12 V12 V BUSMAC INLETCONNECTORON-BOARD CHARGER4–6 L · ENIGHV BATTERY PACKINVERTER4 L · HEAVY CUDC-DC2–4 LBODY2 L PTHLIGHTING1 L · FR-4TELEMATICS4–8 L · Z₀BMS2–4 LHEAVY CU
FIG. 01An EV's electronics, with the board construction each module typically uses.
Layers
1–12
Laminate
FR-4, Tg 170 °C
Copper
1–3 oz, heavier on request
Build class
IPC 2 · 3 on request

01Overview

What makes a PCB fit for a vehicle?

A board in a vehicle lives through what a desktop product never sees: a cold start at dawn and an engine bay in May, constant vibration, condensation, and — in an electric vehicle — hundreds of volts a few millimetres from 3.3 V logic. Many field failures start in the board itself: a cracked via barrel, a lifted pad, a leakage path grown across a damp surface.

We build automotive and EV boards on high-Tg FR-4, with the copper weight, hole plating and spacing each module needs — from double-sided body-control boards to multilayer charger and BMS controllers — and IPC Class 3 when you ask for it.

One thing we say plainly: automotive Tier suppliers specify their own quality requirements, often under IATF 16949. We are ISO 9001:2015 certified, not IATF 16949, and we build to what your drawing and purchase order state. Tell us early which documents your programme needs, and we confirm what we can supply.

Last updated

02Board selection

What boards does a vehicle use?

Vehicle electronics run from 12 V body modules to high-voltage power stages. The construction follows the current, the voltage and where the module is mounted.
What boards does a vehicle use?
Board in the productConstructionBase materialFinishIPC class
01EV charger — AC wallbox or on-board charger control4–6 layer multilayerFR-4, Tg 170 °CENIGClass 2 · 3
02Battery management — cell monitoring and balancingDouble-sided PTH or 4 layerFR-4, Tg 170 °C, heavy copperENIGClass 2 · 3
03Motor controller for e-scooters and e-rickshawsDouble-sided or 4 layerFR-4, heavy copper on power pathsLead-free HASL or ENIGClass 2
04Vehicle lighting — head, tail, DRL and interiorSingle-sidedFR-4, white mask, thermal viasLead-free HASL or ENIGClass 2
05Body electronics — window, seat, wiper, HVACDouble-sided PTHFR-4Lead-free HASL or ENIGClass 2
06Sensors and lamp links in tight or moving spacesFlexible circuitPolyimide with stiffenersENIGClass 2

Two- and three-wheeler EV electronics — controllers, chargers, BMS and lamps — use the same constructions at lower voltage, and usually at higher volume.

03Engineering

Vehicle board problems, and how we solve them

A vehicle combines heat, movement, moisture and high voltage. Each one finds a different weakness in a board.

  • Thermal cycling
  • Vibration
  • Voltage
  • Current
  • Humidity
  • Traceability
  1. P1Thermal cycling

    Thermal cycling cracks plated holes

    FR-4 Tg 170 °C · Class 3 on request

    Why boards fail

    FR-4 expands far more through its thickness than across it, and much faster once it passes its glass transition. Every cold-to-hot cycle stretches the copper barrel of each plated hole; after enough cycles it cracks at the knee or mid-wall and the circuit opens intermittently.

    How we handle it

    We build vehicle boards on high-Tg FR-4 (Tg 170 °C), which stays below its transition across a vehicle's service range and spends less of each reflow above it, so total expansion through the thickness is lower. Holes are plated to the copper thickness your IPC class demands; specify Class 3 on the drawing and we build and inspect to it.

  2. P2Vibration

    Vibration fatigues joints and heavy parts

    Thickness 0.4–3.2 mm

    Why boards fail

    Road and motor vibration flexes the board without pause. Inductors, relays, electrolytic capacitors and connectors load their joints and pads, and a thin, loosely supported board resonates.

    How we handle it

    Pick thickness for stiffness — we build 0.4–3.2 mm — add mounting holes near heavy parts, and anchor connectors with through-hole pins. Our line assembles mixed SMT and through-hole, to IPC-A-610 Class 3 workmanship on request.

  3. P3Voltage

    High voltage needs creepage and a clean surface

    100% electrical test

    Why boards fail

    EV chargers, inverters and battery packs run at hundreds of volts. Surface distance, slot edges and contamination decide whether isolation survives a damp, dusty vehicle for years.

    How we handle it

    Before tooling, CAM checks the gaps between high- and low-voltage nets against your drawing. Isolation slots are CNC-routed and every net is electrically tested. If your design calls for a high-CTI laminate, put it on the drawing and we confirm the material before we start.

  4. P4Current

    Battery and charger boards carry real current

    Copper 1–3 oz

    Why boards fail

    Balancing circuits, contactor drives and charger power paths carry tens of amps continuously. Thin copper overheats, and that rise adds to an already hot enclosure.

    How we handle it

    Copper options: 1 oz (35 µm) and 2 oz (70 µm) standard; 3 oz (105 µm) and heavier on request. Wide pours, parallel vias and heavy copper on the inner layers of a multilayer board keep temperature rise in check without growing the board.

  5. P5Humidity

    Condensation turns residue into leakage

    ENIG · full mask cover

    Why boards fail

    Modules near wheel arches, doors or the charge port see condensation and road salt. Ionic residue or exposed copper becomes a leakage path, then corrosion, once moisture arrives.

    How we handle it

    Solder mask covers everything but the pads, ENIG gives a flat, corrosion-resistant finish, and boards leave in protective packing. Plan conformal coating in your assembly process and mark the keep-out areas on the assembly drawing.

  6. P6Traceability

    Knowing which boards share a lot

    Date code in legend

    Why boards fail

    When a field fault is traced to a board, the first question is which other boards came from the same lot.

    How we handle it

    Every job runs under a job card from CAM to dispatch, and we can add a date code or lot mark to the legend so each board identifies its batch. On turnkey assembly: lot and date-code traceability on every part.

04Thermal cycling

What a cold start does to a plated hole

A plated hole is a copper tube bonded into glass-reinforced epoxy. When the board heats, the epoxy grows through its thickness faster than the copper can follow, and every cycle pulls on the barrel.
FIG. 02APlated hole, 4-layer FR-4, in section
PAD · L1KNEEINNER LAYERS L2 · L3BARREL WALLZ

Expansion exaggerated for clarity. Not to scale.

FIG. 02BA typical vehicle cycle
−40+25+125Tg 150 °CTg 170 °CTIME →°C

Cold soak, warm-up, hot soak, cool-down — repeated through the vehicle's life. The further the hot soak stays below the laminate's Tg, the less the barrel is stretched on each cycle.

  1. FAILURE SITE 01

    Knee crack

    Where the barrel turns onto the pad — the corner takes the most strain on every cycle.

    Plating thickness and annular ring to your IPC class.

  2. FAILURE SITE 02

    Barrel crack

    Mid-wall, where plating is thinnest and the laminate grows most.

    Lower-expansion laminate: FR-4 Tg 170 °C.

  3. FAILURE SITE 03

    Pad cratering

    Resin fractures under the pad of a heavy or stiff part as the board flexes.

    Mounting points near heavy parts; thicker boards for vibration.

05Applications

Automotive and EV applications we build for

From two-wheeler motor controllers to charger cabinets — prototypes and production from the same line.
Two-layer STM32 wireless-node PCB rendered from its Gerbers: green mask, white legend, QFN microcontroller and four mounting holes
FIG. 03A two-layer microcontroller board with a 2.4 GHz radio, rendered from its Gerbers: the size and density of a body-control or telematics sub-module. Board design: STM32 + nRF24 wireless node by denysderihlazov, MIT.
  • A1

    EV chargers

    AC wallbox and DC charger control, metering and communication

    4–6 L
  • A2

    Battery management

    Cell monitoring, balancing and pack controllers

    2–4 L · heavy Cu
  • A3

    Motor controllers

    Gate-drive and control boards for e-scooters and e-rickshaws

    2–4 L
  • A4

    Vehicle lighting

    LED head, tail, indicator and interior lamp boards

    1 L · FR-4
  • A5

    Body electronics

    Window, mirror, seat, wiper and HVAC control modules

    2 L PTH
  • A6

    Aftermarket and accessories

    Trackers, dash cameras, USB chargers and alarm modules

    2–4 L
  • A7

    Workshop and test equipment

    Diagnostic testers, programmers and end-of-line fixtures

    2–6 L

06Specification

A starting specification for vehicle boards

A sound default for automotive and EV modules. Your drawing and your customer's requirements always take precedence.
Recommended starting point · automotive & EV
LaminateHigh-Tg FR-4, Tg 170 °CLower Z-axis expansion through reflow and service
Layer count1 to 12 layers4–6 layers typical for charger, BMS and telematics controllers
Board thickness0.4 mm to 3.2 mm standard; 0.2 mm for thin rigid designsThicker boards resist vibration better
Copper weight1 oz (35 µm) and 2 oz (70 µm) standard; 3 oz (105 µm) and heavier on request
Min. track / space6 mil / 6 mil standard; 4 mil / 4 mil fine-line
Min. drill0.3 mm mechanical; 0.2 mm for fine-pitch designs
Surface finishENIG for flat, corrosion-resistant pads; lead-free HASL for through-hole-heavy boardsAvailable: HASL · LF-HASL · ENIG · OSP
Impedance controlControlled impedance, ±10% tolerance, with stack-up design supportCAN-FD, USB and Ethernet pairs
Build classIPC Class 2; Class 3 on requestState the class on your fab drawing
Electrical test100% electrical test — flying probe or bed-of-nails fixture — plus AOI
AssemblyIPC-A-610 Class 2 standard; Class 3 on request

How to order this spec

Priced online

Simple double-sided prototypes — body-electronics and accessory boards — can be priced live: rigid single- and double-sided boards, 10 mm to 600 mm per side.

Open the instant quote

Reviewed by an engineer

Multilayer, heavy-copper, Class 3 and assembled boards are quoted by an engineer after a DFM review; we aim to reply within 24 hours on working days.

Request a quote

07Standards context

Which automotive standards affect the board?

Vehicle programmes layer several standards over the PCB. Here is what each asks of a board supplier — as context, not as certifications we hold.
IATF 16949
Automotive quality management for the supply chain
Your certification. We hold ISO 9001:2015, not IATF 16949; tell us which customer-specific requirements flow down to the board.
IPC-6012DA
Rigid board performance, with an automotive addendum
We build to Class 2 or, on request, Class 3; put any addendum requirements on the drawing so we confirm them at quote stage.
AEC-Q100 / Q200
Stress qualification of automotive components
Applies to parts, not the bare board. On turnkey builds we buy the qualified parts your BOM names from authorised distributors.
ISO 26262
Functional safety of road-vehicle electronics
A design and process standard for your product; the board's role is consistent, documented construction.
ISO 16750
Environmental conditions and tests for vehicle electronics
Your module is tested to it; laminate, plating and spacing choices are what help it pass.
IS 17017 · IEC 61851
Conductive charging systems for electric vehicles
Applies to your charger; isolation and creepage on the board follow from it.

Stays with you

IATF 16949 certification, PPAP or part-approval packages, AEC-Q component qualification and your module's environmental validation stay with you. Automotive Tier suppliers specify their own quality requirements and flow them down through the drawing and purchase order.

Comes from us

Boards built to IPC Class 2, or Class 3 on request, and to your drawing; high-Tg laminate; a 100% electrical test; an ISO 9001:2015 certified quality management system; and a job card that ties every board to its production lot.

09FAQ

Automotive & EV: common questions

Not covered here? Ask an engineer — we aim to reply within 24 hours on working days.

What PCB is used in automotive electronics?

Most vehicle modules use double-sided or multilayer FR-4, with high-Tg laminate where temperatures run high. Power electronics such as BMS and chargers add heavy copper, LED lamp boards use single-sided FR-4, and sensors in tight spaces use flexible circuits. IPC Class 2 suits most modules; Class 3 is specified for critical ones.

Are you IATF 16949 certified?

No. S.B. Electronics is ISO 9001:2015 certified. Automotive Tier suppliers specify their own quality requirements, often under IATF 16949, and flow them down to their PCB suppliers. Send those requirements with your drawing and we will confirm at quote stage which we can meet, so there are no surprises later in the programme.

Can you build automotive boards to IPC Class 3?

Yes, on request. Class 3 tightens hole-plating thickness, annular ring and acceptance criteria compared with Class 2. State the class on your fab drawing and we quote, build and inspect to it; assembled boards can also be built to IPC-A-610 Class 3 workmanship.

Why use high-Tg FR-4 for vehicle electronics?

Above its glass-transition temperature, FR-4 expands rapidly through its thickness, which strains plated holes during soldering and thermal cycling. A Tg 170 °C laminate stays below that transition longer, so via barrels and pads survive more cycles. It is the usual choice for engine-bay, charger and BMS boards.

Do you make PCBs for electric two- and three-wheelers?

Yes. Electric scooter, motorcycle and e-rickshaw electronics — motor controllers, chargers, battery management and lighting — use the same constructions as car modules at lower voltage: double-sided or four-layer FR-4 with heavy copper on power paths, and single-sided FR-4 boards for LED lamps. Prototypes and production come from the same line.

Automotive & EV

Send the drawing, and your quality requirements with it.

Upload Gerbers, the fab drawing and any customer-specific requirements. An engineer reviews them and replies with a quote that states the class, laminate and test we will build to.