Skip to content
S.B. Electronics Printed circuit boards · since 2000, home page

Products & services

PCB products and services, under one roof.

Eight product lines from one plant in Gandhinagar: bare boards from single-sided to 12 layers, and flexible, then the stencil, parts and assembly that make them working hardware.
FIG. 01SBE-DEMO-04, our 4-layer demo board, exploded. Single-sided is L1; double-sided adds L4; multilayer adds the inner planes.
Layers
1–12
Min. track / space
4 / 4 mil
Finishes
HASL · LF-HASL · ENIG · OSP
Express prototypes
24 h

Overview

Two families, eight product lines.

S.B. Electronics is an ISO 9001:2015 certified printed circuit board manufacturer in Gandhinagar, Gujarat, making boards since 2000. Its eight product lines fall into two families, all made in-house: the bare board, and everything that turns it into a working assembly.

Bare boards are the fabrication side: single-sided, double-sided PTH and NON-PTH, multilayer in 4, 6, 8, 10 and 12 layers, and flexible polyimide circuits, each imaged, etched, masked, finished and electrically tested on our own floor.

Assembly and supply covers laser-cut SMT stencils, components bought from authorised channels, and SMT and through-hole assembly. Order one line or all of them, from a single prototype upwards. Rigid one- and two-layer boards are priced online; everything else is quoted by an engineer, who aims to reply within 24 hours on working days.

01Family A · Bare boards

Which bare PCBs do we fabricate?

Rigid boards from 1 to 12 layers on FR-4 and CEM, and flex on polyimide, all through the same CAM review, plating, etching, mask, finish and 100% electrical test.
FIG. 02SBE-DEMO-04, our own 4-layer reference design, rendered from its Gerbers.

A11–12 L

PCB fabrication

The whole bare-board service: Gerbers in, tested boards out. It covers every rigid and flexible type below — imaged, etched, plated, masked, finished and tested on our own line.

Layer count1 to 12 layers
Base materialsFR-4, FR-2, CEM-1, CEM-3, polyimide
Board thickness0.4–3.2 mm
Copper weight1–3 oz
Surface finishHASL · LF-HASL · ENIG · OSP
Electrical test100% electrical test
PCB fabrication capabilities
Four-layer controller with inner ground and power planesBoard design: ESP32 flight controller by Shazmeen Siddiqui, MIT

A44–12 L

Multilayer PCB

Cores and prepreg laminated into a symmetric stack, with inner ground and power planes. For BGAs, dense controller boards and impedance-controlled lines; every stack-up is reviewed by an engineer before it is quoted.

Multilayer PCB stack-ups
Layers
4, 6, 8, 10 and 12 layers
Track / space
4 mil / 4 mil fine-line
Impedance
±10% tolerance
Polyimide flex circuits under coverlay

A5FLEX

Flexible circuits

Single- or double-sided copper on polyimide film, sealed under a polyimide coverlay, that bends and folds where a rigid board cannot. Stiffeners go under connectors; the circuit replaces harnesses in cameras, wearables and probes.

Flexible circuit design and specs
Polyimide film
12.5, 25 and 50 µm
Track / space
4 mil / 4 mil
Thickness
0.1 mm to 0.3 mm

02Selection guide

Which board type do I need?

Pick the cheapest construction your routing allows: single-sided for simple power and lighting, double-sided PTH for most electronics, multilayer for BGAs and controlled impedance, and flex where the board must bend.

Swipe the table sideways →

Comparison of board constructions: copper layers, relative cost, routing density, typical uses and how to get a price
Board typeSection views, not to scaleSingle-sidedDouble-sided NON-PTHDouble-sided PTHMultilayerFlexible
Copper layers12, unplated holes2, plated holes and vias4–12, inner planes1 or 2, on polyimide film
Relative cost
Lowest
Low
Moderate
Higher; rises with layer count
Higher
Routing density
Low
Low–medium
Medium
Highest
Medium
Typical usesLED drivers, power supplies, chargersSimple through-hole boardsControls, instruments, automotive modulesBGA boards, telecom, controlled impedanceCameras, wearables, medical probes
How to price itInstant quoteInstant quoteInstant quoteRequest a quoteRequest a quote

03Family B · Assembly & supply

Do we assemble, cut stencils and source parts too?

Yes. The team that fabricates your board also cuts its stencil, buys the parts from authorised channels and assembles it on our line.

B1SMT · THT

PCB assembly

SMT, through-hole and mixed-technology boards, from a first article to production runs. Full turnkey, partial turnkey or consigned: we buy every part, some of them, or none.

Smallest part
0201 (imperial) passives
Fine pitch
0.4 mm minimum BGA ball pitch
Inspection
AOI at every stage; X-ray for BGA
Workmanship
IPC-A-610 Class 2 standard
PCB assembly services
FIG. 05BOM review: one NRND part flagged

B3BOM

Component sourcing

Your BOM checked for availability, lifecycle and cost, bought from authorised channels and kitted for our line. Where a part is end-of-life, we propose a drop-in alternative for your approval.

Channel
Authorised distributors and manufacturers only
BOM review
Availability, lifecycle (EOL / NRND) and cost
Traceability
Lot and date-code traceability on every part
Component sourcing for assembly

04One roof

Why order the board, stencil, parts and assembly together?

Every hand-off between suppliers is a chance for a mismatch. One factory means one data pack, one engineering contact and one party answerable for the finished board.
Our SBE-DEMO-04 four-layer demo board stepped four times on a production panel with rails and fiducials
FIG. 06SBE-DEMO-04 on a 2 × 2 production panel: one data pack for board, stencil and placement.
  1. 01 · FAB

    Fabrication

    Built from your Gerbers, panelised with the rails and fiducials the assembly line needs, then 100% electrically tested.

  2. 02 · STN

    Stencil

    Laser-cut from the same paste-layer data as the pads, so every aperture registers with its pad.

  3. 03 · BOM

    Sourcing

    Bought from authorised channels against your BOM, then kitted with lot and date codes recorded.

  4. 04 · PCBA

    Assembly

    Placed, soldered and inspected by AOI, with X-ray where there are BGAs, then packed and dispatched.

Start a project

Send us your Gerbers. We will take it from there.

Price one- and two-layer boards online in seconds, or send the full data pack — Gerbers, drill, BOM and centroid — and an engineer replies with a reviewed quote.