Skip to content
S.B. Electronics Printed circuit boards · since 2000, home page

Industries · Railways

PCB manufacturer for railway electronics

Boards for signalling, traction control, passenger information and on-board electronics — equipment that rides a vibrating vehicle or stands in a trackside cabinet for decades. Multilayer and double-sided FR-4, high-Tg and heavy copper, built to IPC Class 3 on request.

25 kV AC OHEGANDHINAGARTRAIN BUSEVALCAT 1 · BODYCAT 2 · BOGIECAT 3 · AXLETCMS · CAB6–10 LPIS DISPLAY2 LHVAC CONTROL2–4 LTRACTION CONTROL6–8 L · 2 ozAXLE COUNTER4–6 L
FIG. 01A driving car and the track beneath it: where the electronics sit, the board each typically uses, and the IEC 61373 vibration category of each mounting position.
Laminate
FR-4 Tg 170 °C
Copper
1–3 oz
Layers
1–12
Build class
IPC 2 · 3

01Overview

What does railway electronics ask of a PCB?

Railway electronics is defined by its service life. A coach, a locomotive or an interlocking is expected to run for decades, and the boards inside it are expected to last as long — or to be rebuilt, exactly, when they do not.

Rolling stock adds a harsh climate on board: continuous vibration and a shock at every rail joint, under-frame cabinets that bake in summer and start cold in winter, condensation as a train runs from a cold cutting into a humid station, and brake and pantograph dust. Trackside signalling equipment sees much the same from its location box.

The boards that survive it are unremarkable on paper — four- to eight-layer and double-sided FR-4 — and made with care: high-Tg laminate, heavy copper where current flows, generous annular rings, Class 3 plating and solid through-hole joints.

Last updated

02Board selection

Which boards does railway equipment use?

Control and signalling boards go multilayer on high-Tg FR-4; power, I/O and display boards stay double-sided with heavier copper.
Which boards does railway equipment use?
Board in the productConstructionBase materialFinishIPC class
01Axle-counter and track-circuit electronics4–6 layer multilayerFR-4 Tg 170 °CENIGClass 3
02Interlocking and data-logger I/O cardsDouble-sided PTH or 4 layerFR-4ENIG or lead-free HASLClass 2 · 3
03Traction and auxiliary converter control6–8 layer multilayerFR-4 Tg 170 °C, 2 oz copperENIGClass 3
04On-board power supplies (110 V battery input)Double-sided PTHFR-4, heavy copperLead-free HASLClass 2 · 3
05Passenger-information displays and LED boardsDouble-sided PTHFR-4Lead-free HASLClass 2
06Train control, event-recorder and CCTV boards6–10 layer multilayerFR-4, controlled impedanceENIGClass 2 · 3

Relays, transformers and heavy connectors still come through-hole on railway boards. Our line covers reflow, wave and selective / hand soldering, so a mixed board stays with one supplier.

03Engineering

Railway board problems, and how we solve them

A rail vehicle combines an industrial plant's electrical noise with a vehicle's vibration and an outdoor climate, for thirty years. These are the failures the board can prevent.

  • Vibration
  • Thermal
  • Humidity
  • Voltage
  • Lifetime
  1. P1Vibration

    Every rail joint is a shock load

    Thickness 0.4–3.2 mm

    Why boards fail

    Rolling stock vibrates continuously and takes a shock at every rail joint and set of points — hardest at the axle, less on the bogie, least in the body. Transformers, capacitors and relays load their joints; the board flexes; leads and barrels fatigue over the years.

    How we handle it

    Specify a thicker board for large cards (0.4–3.2 mm available) and Class 3 plating for the barrels. Mark heavy parts for staking on the assembly drawing and we confirm it at quotation; through-hole joints are wave- or selectively soldered and inspected to IPC-A-610.

  2. P2Thermal

    Cabinets bake in summer and start cold in winter

    FR-4 Tg 170 °C

    Why boards fail

    EN 50155's hottest classes allow +85 °C air around the equipment, and power parts add their own rise on top; the coldest start at −40 °C. Laminate softens near its glass transition, and every swing strains the plated holes.

    How we handle it

    Use FR-4 Tg 170 °C for traction-control and power boards, so the laminate stays well below its glass transition in service, and Class 3 copper in the barrels for the cycling. Heavier copper, 3 oz (105 µm) and heavier on request, keeps current-carrying tracks cool.

  3. P3Humidity

    Condensation in the station, dust from the brakes

    Tented vias · coating keep-outs

    Why boards fail

    A train running from a cold night into a humid station collects condensation on cold boards, and trackside location boxes breathe damp air every day. Add conductive dust from brakes and pantographs, and leakage paths grow between closely spaced conductors.

    How we handle it

    Full solder-mask coverage with tented vias leaves little bare copper to corrode. Most railway assemblies are conformally coated after assembly: put the material and its keep-outs on your drawing, and we choose a mask and finish it adheres to and agree the coating step at quotation.

  4. P4Voltage

    A battery bus with surges on it

    Spacing checked in CAM

    Why boards fail

    On-board electronics run from the vehicle battery — 24 V to 110 V DC in EN 50155, with 110 V common on coaches — carrying surges and interruptions as loads switch. Inputs need creepage and clearance to the logic, and supply tracks carry real current.

    How we handle it

    CAM checks copper-to-copper spacing against the creepage on your drawing before tooling, and isolation slots are routed to ±0.15 mm as standard. Supply tracks get the copper weight their current needs, and the 100% net test proves the isolation.

  5. P5Lifetime

    Vehicles outlive the parts their boards were designed around

    No MOQ · EOL review

    Why boards fail

    Rolling stock and signalling are maintained for decades. Spares are ordered years after the first build, in small numbers, and some of the original components are end-of-life by the time the depot asks for more.

    How we handle it

    There is no minimum order, so ten spare cards are a normal job. Your specification stays on file for the repeat, and our BOM review flags end-of-life parts and proposes drop-in alternatives for your approval. Authorised distributors and manufacturers only.

04Applications

Railway equipment we build boards for

Signalling, rolling stock and stations — boards for new equipment, and spares for equipment already in service.
Production panel of four SBE-DEMO-04 four-layer boards with rails, fiducials, tooling holes and a date code in the legend
FIG. 02Four boards on one production panel, made, tested and recorded together under one job number: a board returned from the field traces back to its panel and its lot. SBE-DEMO-04, our own four-layer design.
  • A14–6 L

    Train detection

    Axle counters, track circuits and detection evaluators

  • A22–6 L

    Electronic interlocking

    Vital I/O, relay-interface and object-controller cards

  • A36–8 L · 2 oz

    Traction and auxiliary converters

    Control, gate-drive and measurement boards

  • A42–4 L

    Passenger information

    PIS and PA controllers, LED destination and coach displays

  • A56–10 L

    Train control and recording

    Train-network nodes, event recorders and CCTV recorders

  • A62–4 L

    Coach systems

    Lighting, HVAC, door and fire-detection controllers

  • A72–6 L

    Stations and trackside

    Level-crossing, point-machine and station equipment controllers

  • Not listed?Send the drawing and a line about where the board will be used.Ask an engineer

05Specification

A starting specification for railway boards

A sound default for rolling-stock and signalling boards. Your drawing wins on every line.
Recommended starting point · railway electronics
Construction4–8 layer multilayer for control and signalling; double-sided PTH for power, I/O and displaysRange: 1 to 12 layers
LaminateFR-4 Tg 170 °CFR-4 Tg 150 °C for low-power boards in mild locations
Board thickness1.6 mm; 2.0–2.4 mm for large or heavily loaded cardsRange: 0.4 mm to 3.2 mm standard; 0.2 mm for thin rigid designs
Copper weight1 oz (35 µm) and 2 oz (70 µm) standard; 3 oz (105 µm) and heavier on request
Min. track / space6 mil / 6 mil standard; 4 mil / 4 mil fine-lineWider spacing on supply and I/O nets, per your creepage
Annular ring0.15 mm minimum for drilled holes (design guideline)
Surface finishENIG for multilayer control boards; lead-free HASL for through-hole-heavy power and I/O boardsAvailable: HASL · LF-HASL · ENIG · OSP
Mask and legendGreen mask; white legend with part number, revision and date code
Electrical test100% electrical test — flying probe or bed-of-nails fixture — plus AOI
AssemblySMT, through-hole (THT) and mixed technology; reflow, wave and selective / hand solderingIPC-A-610 Class 2 standard; Class 3 on request
ComponentsAuthorised distributors and manufacturers only — no grey-market or broker stockLot and date-code traceability on every part

How to order this spec

Priced online

Double-sided display, I/O and power boards — rigid single- and double-sided boards — can be priced online for prototypes and spares: 1 to 100,000 boards per line, dispatch in 3, 5, 7 or 10 working days.

Open the instant quote

Reviewed by an engineer

Multilayer control boards, Class 3 builds, heavy copper, assembly and coating requirements are quoted by an engineer, who aims to reply within 24 hours on working days.

Request a quote

06Standards context

Which standards apply to railway electronics?

Railway equipment is qualified as a product, by its maker, for a railway. These are the standards and approvals behind that, and where the board comes in.
EN 50155
Railway applications — electronic equipment on rolling stock
Operating-temperature classes OT1–OT6, supply-voltage range and interruptions, and the type tests the finished unit must pass.
IEC 61373
Rolling-stock equipment — shock and vibration tests
Category 1 body-mounted, 2 bogie-mounted, 3 axle-mounted: the mounting position sets the test severity.
EN 50121-3-2
EMC of rolling-stock apparatus
Emission and immunity of the equipment; ground planes and filtering on the board are where much of it is won.
EN 45545-2
Fire protection on railway vehicles — requirements for materials
Fire behaviour of the equipment's materials, assessed by its maker; ask for laminate datasheets with the quotation.
RDSO specifications
Indian Railways' technical specifications and vendor approval
Approval belongs to the equipment maker, for its product; the boards are built to that maker's drawing.

Stays with you

EN 50155 compliance, IEC 61373 and EN 50121 testing, the fire-safety assessment, RDSO or operator approval and the equipment's safety case stay with the maker that supplies the railway. We are not an RDSO-approved vendor and do not claim to be.

Comes from us

Boards built to IPC Class 2 by default and Class 3 on request, to your drawing and stack-up, on high-Tg FR-4 where specified, with AOI, a 100% electrical test, final inspection to IPC-A-600 and an ISO 9001:2015 certified quality management system.

07EN 50155 context

Temperature classes, and where the laminate sits

EN 50155 sorts on-board equipment into operating-temperature classes, OT1 to OT6. Plotted against the glass transition of the FR-4 we build with, the cabinet air is rarely the problem — the hot spots on a power board are.
FIG. 02Operating-temperature classes against laminate Tg
  1. OT1−25…+55 °C
  2. OT2−40…+55 °C
  3. OT3−25…+70 °C
  4. OT4−40…+70 °C
  5. OT5−25…+85 °C
  6. OT6−40…+85 °C
  7. Hot spotOT6 + rise
EN 50155 class, °C ambientFR-4 Tg 150 °CHigh-Tg FR-4, Tg 170 °CLocal rise over a power part, design-dependentMargin: 65 K / 85 K

Classes per EN 50155:2017, air temperature around the equipment. Context for your design; the standard applies to your equipment, not to the bare board.

  1. N1

    The cabinet is rarely the limit

    Even OT6's +85 °C leaves 65 K to the Tg of standard FR-4. Power parts eat into that margin locally, which is why traction-control and converter boards go to Tg 170 °C.

  2. N2

    Cycling is the slow failure

    A daily swing from a cold start to full load, repeated for decades, fatigues plated barrels. Class 3 hole-wall copper and a generous annular ring buy the extra life.

  3. N3

    Cold starts bring condensation

    OT2, OT4 and OT6 start at −40 °C. Warming in humid air condenses water on the board: tented vias, full mask coverage and a conformal coat keep it off the copper.

09FAQ

Railways: common questions

Not covered here? Ask an engineer — we aim to reply within 24 hours on working days.

What PCB is used in railway electronics?

Mostly four- to eight-layer FR-4 for control and signalling boards and double-sided PTH for power, I/O and display cards, usually on high-Tg laminate with heavy copper where current flows. Railway boards are typically built to IPC Class 3, assembled with robust through-hole joints and conformally coated.

Are you RDSO approved or EN 50155 certified?

No. EN 50155 applies to finished on-board equipment, and RDSO approval is granted to the equipment maker for its product — neither is held by a board supplier on the maker's behalf. We are ISO 9001:2015 certified and build boards to IPC Class 3 and your drawing on request.

Who makes railway PCBs in India?

Railway electronics makers in India buy boards from domestic and overseas PCB manufacturers, built to their own drawings. S.B. Electronics, in the G.I.D.C. Electronics Estate, Gandhinagar, has made PCBs since 2000 and builds double-sided and multilayer boards and assemblies for signalling, rolling-stock and passenger-information equipment.

Which laminate suits EN 50155 temperature classes?

Standard FR-4 (Tg 150 °C) suits most boards, even at OT6's +85 °C ambient, because its glass transition is well above the cabinet air. Choose Tg 170 °C for power and traction-control boards, where components heat the laminate locally, and for thick many-layer boards that cycle hard.

Can you supply small batches of spare boards for older equipment?

Yes. There is no minimum order, so a batch of ten spares for a fleet already in service is a normal job. Send Gerbers, drill data and the drawing; if parts have gone end-of-life, our BOM review proposes drop-in alternatives for your approval before anything is built.

Railways

Send the drawing — for the first build and every spare after it.

Upload Gerbers, drill files, the drawing and your class, laminate and coating requirements. An engineer reviews them and replies with a quote; double-sided spares can be priced online straight away.