Skip to content
S.B. Electronics Printed circuit boards · since 2000, home page

Industries · Renewable energy

Solar inverter PCB manufacturer for renewable energy

Power boards for string and hybrid inverters, MPPT charge controllers, battery management systems and energy-storage converters: circuits that carry tens of amps at hundreds of volts DC, outdoors, for as long as the panels feeding them. Heavy copper, high-Tg FR-4 and routed isolation slots, made in Gandhinagar since 2000.

C1C2C3Q1Q3Q2Q4L1L2U2U3U4U5DSPPV+PV−DC LINKACISOLATION SLOTJ3 COMMPWR-STAGE · 2 OZ · FR-4 TG170ABCDE

FIG. 01Top copper of a single-phase inverter power stage. The dashes trace the load current.

  • ADC+ and DC− pours in 2 oz copper, stitched with via rows
  • BDC-link capacitors across the DC+ / DC− gap
  • CFull bridge: TO-263 switches on copper heat-spreading tabs
  • DRouted isolation slot, gate-driver isolators across it
  • ELow-voltage control section with the DSP
Copper
1–3 oz and heavier
Laminate
FR-4 Tg 170 °C
Board thickness
0.4–3.2 mm
Electrical test
100% of boards

01Overview

What does a solar inverter ask of its PCB?

A solar inverter is a small power station in a sealed box. Its boards switch tens of amps on a DC link of several hundred volts, sit in an enclosure that bakes on a roof or a ground-mount frame, and are expected to keep converting for twenty years or more.

That shapes the board in three ways: copper thick enough to carry the current without cooking the laminate around it, spacing and routed slots wide enough for the DC voltage, and a laminate that survives a daily heat cycle for decades. The control, communication and BMS boards beside the power stage are ordinary FR-4 multilayers; the hard engineering sits on the power board.

Axpert is on our customer list. The first prototype of a new MPPT stage and the repeat batch of a charge controller already in the market come off the same line in Gandhinagar, built to the same drawing every time.

Last updated

02Board selection

Which boards go into an inverter or a battery system?

One product, several constructions. The power stage carries the current; the boards around it measure, decide and communicate.
Which boards go into an inverter or a battery system?
Board in the productConstructionBase materialFinishIPC class
01Inverter power stage (DC link, H-bridge, output filter)Double-sided PTH, heavy copperFR-4, Tg 170 °CLead-free HASLClass 2 · 3
02MPPT boost and DC-DC stagesDouble-sided or 4 layerFR-4, 2 oz copperLead-free HASLClass 2
03Control and DSP board4–6 layer multilayerFR-4ENIGClass 2
04Isolated gate-driver board4 layer multilayerFR-4, Tg 170 °CENIGClass 2 · 3
05BMS cell-monitor and balancing boardDouble-sided or 4 layerFR-4ENIGClass 2 · 3
06PWM and small MPPT charge controllersDouble-sided PTHFR-4, 2 oz copperLead-free HASLClass 2

Surface-mount MOSFETs and diodes that need a heat path are backed by wide copper pours and rows of thermal vias to the enclosure. Copper weights: 1 oz (35 µm) and 2 oz (70 µm) standard; 3 oz (105 µm) and heavier on request.

03Copper and current

How wide does a power track need to be?

IPC-2221 links current, temperature rise and copper cross-section. Hold the current and the rise, double the copper weight, and the track needs roughly half the width: the reason inverter power boards are built in 2 oz and heavier copper.

Outer layer · 10 °C rise · IPC-2221

  • 1 oz
  • 2 oz
  • 3 oz
  1. 5A0.10 mm²2.8 mm1.4 mm0.92 mm
  2. 10A0.25 mm²7.2 mm3.6 mm2.4 mm
  3. 20A0.66 mm²18.7 mm9.4 mm6.2 mm
  4. 30A1.1 mm²32.7 mm16.4 mm10.9 mm
FIG. 02Copper cross-sections at true width, thickness exaggerated. The area under each current is the same whatever the weight.
  1. N1The formula behind the bars

    I = k · ΔT0.44 · A0.725, where A is the cross-section in mil² and k is 0.048 for outer layers. Width × thickness = A, so twice the copper needs half the width for the same current.

  2. N2Inner layers need more copper

    An inner track cannot shed heat to the air, so k halves and the same current needs about 2.6× the cross-section: 24.3 mm of 2 oz for 20 A instead of 9.4 mm on the surface.

  3. N3A starting point, not a sign-off

    IPC-2152 refines the estimate with board thickness, nearby planes and mounting, and often allows narrower tracks. Use it, or a thermal simulation, for the final width.

  4. N4What we build

    1 oz (35 µm) and 2 oz (70 µm) standard; 3 oz (105 µm) and heavier on request. Heavier copper needs wider gaps to etch cleanly, so ask for the minimum track and space at your copper weight before layout.

04Engineering

Power-board failures, and how we build against them

Inverters and battery systems fail slowly: a track that runs hot for years, a surface that tracks under DC, a plated hole that cracks after its seven-thousandth sunrise.

  • Current
  • Voltage
  • Thermal cycling
  • Humidity
  • Signal integrity
  1. P1Current

    Tens of amps through a copper track

    Copper 1–3 oz · 35–105 µm

    Why boards fail

    Temperature rise follows current, copper cross-section and how easily heat leaves the board. A track sized on a calculator for 2 oz but built in 1 oz runs hot, browns the laminate around it and drifts the current-sense reading next to it.

    How we handle it

    Size the copper for the current. We build 1 oz (35 µm) and 2 oz (70 µm) standard; 3 oz (105 µm) and heavier on request. Doubling the copper roughly halves the width a track needs (drawn to scale below), and wide pours stitched to the other side with rows of plated vias share the load.

  2. P2Voltage

    Hundreds of volts DC across the surface

    Routed slots · CTI on the drawing

    Why boards fail

    PV strings reach 1,000 V DC, and 1,500 V in utility plants; a residential DC link sits around 400 V. DC never crosses zero, so once dust and moisture start a leakage path along the surface, it keeps growing into a carbonised track.

    How we handle it

    CAM checks copper-to-copper and copper-to-edge spacing against your drawing before tooling. Isolation slots are CNC-routed at their finished width to ±0.15 mm (±0.1 mm on request). If your creepage calculation assumes a laminate CTI above standard FR-4, state it on the drawing and we confirm the laminate at quote.

  3. P3Thermal cycling

    A heat cycle every day for twenty years

    FR-4 Tg 170 °C · Class 3 on request

    Why boards fail

    Each sunrise heats the power stage and each sunset cools it: more than 7,000 cycles over a twenty-year design life. Laminate expands through its thickness far more than the copper barrel of a plated hole, so thin plating cracks at the corner of the hole.

    How we handle it

    Build power boards on Tg 170 °C FR-4, which expands less in the z-axis below its Tg, and specify IPC Class 3 where life matters: thicker hole-wall copper and tighter acceptance on every plated hole.

  4. P4Humidity

    Condensation inside an outdoor enclosure

    LPI mask · LF-HASL or ENIG

    Why boards fail

    Charge controllers and inverters live on rooftops, in battery rooms and in pump houses, where night-time condensation and fine dust settle on the board. Moisture on bare copper between high-voltage nets starts leakage first and corrosion later.

    How we handle it

    Keep solder mask over every high-voltage track and open it only where something is soldered; we hold the mask layer as drawn. Lead-free HASL or ENIG seals the exposed pads. If the assembly is conformally coated, leave the keep-outs for connectors and test points in the layout.

  5. P5Signal integrity

    Millivolt cell readings beside a switching stage

    4 L · continuous ground plane

    Why boards fail

    A BMS measures each cell to a few millivolts while a converter switches tens of amps nearby. Switching noise and balancing currents couple into the sense lines, and the state-of-charge estimate wanders.

    How we handle it

    Put the cell-monitor front end on four layers with an unbroken ground plane, route sense lines as tight pairs away from the power pours, and keep heavy copper on the power board. We build 4, 6, 8, 10 and 12 layers with stack-up support.

05Applications

Renewable-energy products we make boards for

Solar, storage and the power conversion between them, from a single prototype to scheduled repeat production.
Four-layer ESP32 power-control PCB rendered from its Gerbers: four switching devices on a copper pour at one end, the radio module at the other
FIG. 03A four-layer power-control board, rendered from its Gerbers: switching devices on a copper pour at one end, the ESP32 radio at the other — the power-and-logic split inverter and charge-controller boards share. Board design: ESP32 ATX power controller by William Vallet, MIT.
  • A1

    String and hybrid solar inverters

    Power stage, control, gate-drive and communication boards

    2–6 L · heavy Cu
  • A2

    MPPT and PWM charge controllers

    Boost or buck stage and its controller, often on one board

    2 L · 2 oz
  • A3

    Battery management systems

    Cell-monitor, balancing and pack-controller boards

    2–4 L · ENIG
  • A4

    Energy-storage converters

    Bidirectional DC-DC and power-conversion-system control

    4–8 L
  • A5

    Solar pump controllers

    Motor-drive boards for agricultural PV water pumps

    2–4 L · heavy Cu
  • A6

    Micro-inverters and optimisers

    Dense power boards that sit behind each panel

    4 L · Tg 170
  • A7

    Monitoring and data loggers

    Wi-Fi, GSM and RS-485 monitoring and metering boards

    2–4 L

06Specification

A starting specification for power boards

A sound default for inverter, charge-controller and BMS boards. Your drawing always wins: change any line and we quote what you specify.
Recommended starting point · renewable energy
ConstructionDouble-sided PTH for power stages; 4–6 layers for control, gate-drive and BMSRange: 1 to 12 layers
LaminateFR-4 Tg 170 °C for power boards; standard FR-4 for controlState any CTI requirement on the drawing
Board thickness1.6 mm default; up to 3.2 mm for large, terminal-loaded power boardsRange: 0.4 mm to 3.2 mm standard; 0.2 mm for thin rigid designs
Copper weight1 oz (35 µm) and 2 oz (70 µm) standard; 3 oz (105 µm) and heavier on request2 oz is the usual starting point for a power stage
Min. track / space6 mil / 6 mil standard; 4 mil / 4 mil fine-lineHeavier copper needs wider gaps: ask before layout
Min. drill0.3 mm mechanical; 0.2 mm for fine-pitch designs
Isolation slotsCNC-routed at finished width, ±0.15 mm as standard; ±0.1 mm on request
Surface finishLead-free HASL for power boards; ENIG for control and BMSAvailable: HASL · LF-HASL · ENIG · OSP
Solder maskGreen LPI over all high-voltage copper; openings only where soldered
Electrical test100% electrical test — flying probe or bed-of-nails fixture — plus AOI
AssemblySMT, through-hole (THT) and mixed technologyReflow, wave and selective / hand soldering
ComponentsAuthorised distributors and manufacturers only — no grey-market or broker stock

How to order this spec

Priced online

Simple charge-controller and auxiliary-supply boards (rigid single- and double-sided boards) are priced live: 10 mm to 600 mm per side, 1 to 100,000 boards per line, dispatch in 3, 5, 7 or 10 working days.

Open the instant quote

Reviewed by an engineer

Heavy-copper power stages, multilayer control and BMS boards, assembly and sourcing are quoted by an engineer, who aims to reply within 24 hours on working days.

Request a quote

07Standards context

Which standards apply to inverters and storage?

Your inverter or battery system is approved as a product. These are the standards it is tested to, and where the board enters each one.
IEC 62109-1 / -2
Safety of power converters for photovoltaic systems
Insulation, creepage and clearance for PV inverters and charge controllers, for DC inputs up to 1,500 V.
IS 16221
Indian adoption of IEC 62109 (Parts 1 and 2)
The standard behind BIS registration of solar inverters sold in India.
IEC 62477-1
Safety of power electronic converter systems
General insulation coordination for converters, including storage power-conversion systems.
IEC 62619
Safety of lithium cells and batteries for industrial use
Energy-storage batteries; the BMS is part of the safety case it asks for.
IEC 60664-1
Insulation coordination for low-voltage equipment
Creepage tables by working voltage, pollution degree and the laminate's CTI material group.
UL 94 V-0
Flammability of plastic materials
The flammability class FR-4 laminates are rated to by their makers. Board-level UL recognition is a separate listing we do not hold.

Stays with you

Product safety approval (IEC 62109, IS 16221 and BIS registration where it applies), grid-connection compliance and battery-system certification stay with the inverter or storage maker. The board is one tested component of that product.

Comes from us

Boards built to IPC Class 2 by default and Class 3 on request, to your drawing, copper weight and spacing, with AOI, a 100% electrical test, final inspection to IPC-A-600 and an ISO 9001:2015 certified quality management system.

09FAQ

Renewable energy: common questions

Not covered here? Ask an engineer — we aim to reply within 24 hours on working days.

What PCB is used in a solar inverter?

A solar inverter usually combines a double-sided or four-layer power board with 2 oz or heavier copper on high-Tg FR-4 for the DC link and switching bridge, a four- to six-layer control board with ENIG for the processor, and isolated gate-driver boards between them. Power boards are often thicker than 1.6 mm.

What copper weight do inverter and BMS power boards need?

It follows the current. For a 10 °C rise, a 20 A track on an outer layer needs about 18.7 mm of 1 oz copper but 9.4 mm of 2 oz, by the IPC-2221 approximation. Most power stages start at 2 oz. We build 1 and 2 oz as standard, and 3 oz and heavier on request.

Who makes solar inverter PCBs in India?

S.B. Electronics manufactures PCBs for solar inverters, charge controllers and battery management systems in the G.I.D.C. Electronics Estate, Gandhinagar, Gujarat. We have made printed circuit boards since 2000: single- and double-sided, and multilayer up to 12 layers, with assembly and component sourcing in-house.

How do you handle creepage on high-voltage DC boards?

Creepage is designed into your layout from the standard your product follows, such as IEC 62109-1 for PV inverters. We hold what you draw: CAM checks copper spacing before tooling, isolation slots are CNC-routed at their finished width, and a 100% electrical test proves that no two nets touch.

Can you build and assemble BMS boards for lithium battery packs?

Yes. Cell-monitoring and balancing boards are usually double-sided or four-layer FR-4 with ENIG, with sense lines kept apart from the high-current path, while busbar and contactor boards take heavier copper. We assemble them too, with parts from authorised distributors and lot and date-code traceability.

Renewable energy

Send the power board. We will build the copper you drew.

Upload Gerbers, drill files and your fabrication drawing with copper weight, thickness and any CTI or class requirement. An engineer reviews them and replies with a quote.