Skip to content
S.B. Electronics Printed circuit boards · since 2000, home page

Industries · LED lighting

PCB manufacturer for LED lighting

Single-sided FR-4 and CEM LED boards and driver boards, built by the panel-load, for luminaire, lamp and driver makers. Made in Gandhinagar, where we have built PCBs since 2000.

D1D2D3D4D5D6D7D8D9D10D11D12−+SBE-DL12FR-4 · 1 LFR-4 · 1 LD1–D12 · ONE STRINGWHITE MASK · BLACK LEGENDM3 × 3
FIG. 01Downlight module, plotted: twelve LEDs in one series string on a single-sided FR-4 board with white mask.
LED and driver boards
1 L and 2 L FR-4 / CEM
Copper
1–3 oz
Mask for reflectance
White
Minimum order
None

01Overview

What does an LED lighting PCB need?

Most LED products carry two boards with opposite priorities. The LED board holds the emitters, and its real job is moving heat out of each LED's thermal pad fast enough to keep the junction cool. The driver board turns mains into a steady current — safely, cheaply and in volume.

So LED work runs on two constructions on our floor. Single-sided and double-sided FR-4 and CEM boards carry the drivers, dimming controls and low-power lamp engines, often thousands at a time, with thermal-via arrays under the LED pads where the board has to shed heat.

Both are built in-house in Gandhinagar, with white or green solder mask, a lead-free finish when you need RoHS, and a 100% electrical test before packing.

Last updated

Lighting brands among our customers

  • Wipro Lighting
  • Philips
  • Syska
  • Bajaj Electricals

02Board selection

What boards does LED lighting need?

Match the construction to the board's job. The LED board is chosen for its heat path; the driver board for isolation, cost and volume.
What boards does LED lighting need?
Board in the productConstructionBase materialFinishIPC class
01High-power LED module — street, flood and high-baySingle-sidedFR-4, white mask, thermal-via arrays under the padsLead-free HASL or ENIGClass 2
02Downlight and panel-light modulesSingle-sidedFR-4, white maskLead-free HASL or OSPClass 2
03Linear strips and tube-light boardsSingle-sidedFR-4 or CEM-3, white maskLead-free HASL or OSPClass 2
04Mains LED driver — isolated or non-isolatedSingle-sidedCEM-1 or FR-4HASL or lead-free HASLClass 2
05Smart and dimmable driver with MCU or radioDouble-sided PTHFR-4ENIG or lead-free HASLClass 2

Plain one- and two-layer rigid boards can be priced online in the instant quote. Assembly and stencils are quoted by an engineer.

03Thermal path

Where the heat goes on an FR-4 board

The heat from each LED pad crosses the laminate through a thermal-via array, reaches the backside copper, and spreads sideways into a mounting face or heat sink. More vias, wider copper and a white mask keep the junction cool.
FIG. 02APlain FR-4 board
LED · THERMAL PADHEAT TRAPPEDFR-4 LAMINATE · 1.6 MMHOUSING / HEATSINK
Copper, 1 oz
≈ 390 W/m·K
FR-4 laminate, 1.6 mm
≈ 0.3 W/m·K
Bottom copper
≈ 390 W/m·K, disconnected
Junction temperatureHotter
FIG. 02BFR-4 with a thermal-via array
LED · THERMAL PADHEAT PULLED DOWNFR-4 LAMINATE · 1.6 MMTHERMAL-VIA ARRAYHOUSING / HEATSINK
Copper, 1 oz
≈ 390 W/m·K
Thermal vias → bottom copper
≈ 390 W/m·K
Housing / heat sink
Metal, mounted face
Junction temperatureCooler

Thermal conductivity · W/m·K · log scale · typical material values

0.1
1
10
100
1000
FR-4 laminate≈ 0.3
Copper (via wall)≈ 390

Worked example · per unit area

A layer's thermal resistance is its thickness divided by its conductivity. With typical values, the path under the LED compares like this:

1.6 mm of FR-4, no vias
≈ 53 K·cm²/W
Thermal-via array → bottom copper
A few K·cm²/W

The via array is where the difference comes from: each plated hole is a copper shortcut through the insulating laminate, and enough of them in parallel drop the junction temperature by tens of degrees. That is why we count vias as a first-class design item and size the array to the LED's thermal load.

04Engineering

LED board problems, and how we solve them

LED products rarely fail at the LED itself. They fail because the board ran hot, a driver lost its isolation, or the mask changed colour between batches.

  • Thermal
  • Current
  • Optics
  • Voltage
  • Cost
  1. P1Thermal

    Heat has to leave the LED through the board

    Thermal-via arrays · FR-4

    Why boards fail

    Every degree at the junction costs light output and lifetime. On plain FR-4, heat from the thermal pad must cross 1.6 mm of laminate that conducts about 0.3 W/m·K, so the junction runs hot and lumen maintenance drops early.

    How we handle it

    For LEDs that carry heat, we put a thermal-via array under each pad so the junction's heat reaches the backside copper and spreads into a mounting face or heat sink. State the thermal duty on your drawing and we confirm the via count and copper weight at quote stage.

  2. P2Current

    Track width sets the temperature of the LED string

    Copper 1–3 oz

    Why boards fail

    Series strings and driver output stages carry continuous current for years. Thin copper and narrow tracks heat up, and on a densely packed module that heat adds to the LEDs' own.

    How we handle it

    Copper options: 1 oz (35 µm) and 2 oz (70 µm) standard; 3 oz (105 µm) and heavier on request. Heavier copper lets high-current tracks stay narrow enough to fit the layout, and wide pours on the LED side spread heat sideways before it has to cross the dielectric.

  3. P3Optics

    Solder mask colour changes the light

    White mask · black legend

    Why boards fail

    On the LED side the board is part of the optical system. A dark or yellowing mask absorbs light the reflector was designed to use, and a shade change between batches shows in the finished fitting.

    How we handle it

    White solder mask is one of our 6 standard colours; pair it with black legend so designators stay readable. Specify it on the fab drawing and every repeat order is printed with the same mask.

  4. P4Voltage

    Mains on a driver board needs distance

    Isolation slots · 100% E-test

    Why boards fail

    An offline driver puts rectified mains a few millimetres from the low-voltage output. Creepage lost to a copper sliver, a mis-registered mask opening or a burr in an isolation slot can fail a safety test, or a fitting in the field.

    How we handle it

    CAM engineers check copper-to-copper and copper-to-edge spacing against your drawing before tooling. Isolation slots are CNC-routed (±0.15 mm as standard; ±0.1 mm on request), and every net is electrically tested for shorts.

  5. P5Cost

    Price per board decides the order

    V-score panels · no MOQ

    Why boards fail

    Lighting is a price-driven market. A driver board that costs a little too much, or arrives in mixed lots, does more damage than almost any engineering defect.

    How we handle it

    Single-sided boards take the shortest route through our factory: no hole plating, no lamination. We step-and-repeat them on production panels with V-scores for quick depanelling, and keep repeat orders on the same material and process.

05Applications

Where our LED lighting boards go

From the first prototype of a new luminaire to repeat production of a driver that has been on the market for years.
Single-sided 5 V power-supply PCB rendered from its Gerbers: green mask, white legend for J1, J2, D1, C1 to C3 and U1
FIG. 03A single-sided 5 V supply: rectifier, smoothing capacitor and a three-pin regulator, with every track on one copper layer — the construction of most LED drivers and lamp engines. Board design: Single-sided 5 V power supply by Mimo-Mir, MIT.
  • A1

    Street and flood lights

    High-power LED modules and the isolated driver behind them

    1 L
  • A2

    High-bay and industrial luminaires

    High-power modules where heat decides service life

    1 L · thermal vias
  • A3

    Downlights and panel lights

    Round and square LED modules with white mask

    1 L
  • A4

    LED bulbs and tube lights

    Lamp engines and compact non-isolated drivers

    1 L
  • A5

    Strips and linear fittings

    Long, narrow single-sided boards on panels

    1 L
  • A6

    Smart and dimmable lighting

    Drivers with an MCU, DALI or wireless control

    2 L PTH
  • A7

    Emergency lighting

    Battery charger and changeover boards

    1–2 L

06Specification

A starting specification for LED boards

A sound default for most LED products. Your drawing always wins: change any line and we quote what you specify.
Recommended starting point · LED lighting
LED moduleSingle-sided FR-4, white mask, thermal-via arrays under the pads
Driver boardSingle-sided FR-4 or CEM-1 / CEM-3; double-sided PTH for MCU control
Board thickness0.4–3.2 mm1.6 mm is the usual default for drivers
Copper weight1 oz (35 µm) and 2 oz (70 µm) standard; 3 oz (105 µm) and heavier on request
Solder maskWhite on the LED side; green on driversAvailable: Green, Red, Blue, Black, White, Yellow
LegendBlack on white mask; white on greenAvailable: White, Yellow, Black
Surface finishLead-free HASL or OSP for drivers; ENIG for fine-pitch LED padsAvailable: HASL · LF-HASL · ENIG · OSP
PanelisationV-score, tab-routing (mouse bites) or a combination; rails, fiducials and tooling holes
Electrical test100% electrical test — flying probe or bed-of-nails fixture — plus AOI
Minimum orderNo minimum order quantity — one prototype board upwards

Standards context

Which standards apply to an LED product?

Your luminaire or driver is approved against product safety standards. The board is one input to that approval; here is where it touches each one.

IEC 61347
Lamp controlgear — safety of LED drivers
Sets the creepage and clearance your driver layout must keep; we hold copper and slots to your drawing.
IEC 60598
Luminaires — general safety requirements
Covers the finished fitting; board material and temperature ratings feed into its assessment.
IEC 62031
LED modules for general lighting — safety
Applies to the LED module; its documentation cites the board construction.
BIS (CRS)
Compulsory registration of LED lamps, luminaires and drivers sold in India
Indian standards that mirror the IEC ones above; registration belongs to the brand owner.
RoHS
Restriction of hazardous substances
Order lead-free HASL, ENIG or OSP and tell us the product must comply.
Comes from us
We build to IPC Class 2 by default, Class 3 on request, and to your drawing, inside an ISO 9001:2015 certified quality management system: AOI, a 100% electrical test and final inspection to IPC-A-600 on every order.

Stays with youProduct approval — IEC or BIS safety, photometry, EMC and registration — belongs to the luminaire or driver brand. The board's part is to be built exactly as specified, the same way on every repeat order.

How to order this spec

Priced online

Rigid single- and double-sided boards — most driver and control boards — are priced live: 10 mm to 600 mm per side, 1 to 100,000 boards per line, dispatch in 3, 5, 7 or 10 working days.

Open the instant quote

Reviewed by an engineer

Assembled drivers and stencils go to an engineer, who aims to reply with a reviewed quote within 24 hours on working days.

Request a quote

08FAQ

LED lighting: common questions

Not covered here? Ask an engineer — we aim to reply within 24 hours on working days.

What PCB is used in LED lighting?

Most LED products use two boards. The LED module is usually a single-sided FR-4 board, with thermal-via arrays under the pads to carry heat away from the LEDs, and a white mask for reflectance. The driver is usually a single-sided FR-4 or CEM board, or a double-sided PTH board when it carries a microcontroller or a wireless module.

How do you cool high-power LEDs on an FR-4 board?

Where the LEDs dissipate enough heat that plain FR-4 would let the junction run hot, we put a thermal-via array under each pad so the heat reaches the backside copper and spreads into a mounting face or heat sink. For low-power LEDs and widely spaced mid-power strips, a copper pour and a few vias are enough. Let your thermal calculation decide.

Why do LED boards use white solder mask?

White mask reflects light that a green or black board would absorb, so more of the LEDs' output leaves the fitting, and the board looks clean behind a diffuser. It is one of our 6 standard mask colours. Ask for black legend so reference designators stay readable on the white surface.

Can you manufacture LED driver boards in volume?

Yes. Single-sided driver boards take the shortest route through our factory: no hole plating and no lamination. We panelise them with V-scores for fast depanelling, test every net electrically and keep repeat orders on the same material. There is no minimum order, so the pilot batch and the production run come off the same line.

Are your LED boards RoHS compliant?

They can be. Order lead-free HASL, ENIG or OSP as the surface finish and tell us the product must be RoHS compliant, and the boards are built without lead in the finish. Leaded HASL stays available for products outside RoHS scope. Note the requirement on your fab drawing so it carries over to every repeat order.

LED lighting

Send the LED board and the driver together.

Upload Gerbers for both; an engineer quotes the LED module and the driver side by side, with construction, finish and panel layout confirmed.