Skip to content
S.B. Electronics Printed circuit boards · since 2000, home page

Industries · Medical electronics

PCB manufacturer for medical electronics

Bare boards and assemblies for patient monitors, diagnostic instruments and laboratory equipment: fine-pitch multilayers with ENIG, built to IPC Class 3 when your device needs it, with a job record behind every board. Your device's regulatory file stays yours; we build exactly what it specifies.

II25 mm/sHR75SpO₂ %98PATIENT SIDEFLOATING APPLIED PARTSYSTEM SIDEMAINS-REFERENCEDRALALLRLVGUARDAFEISO DC-DCDIGITAL ISOLATOR8 mmL1U4 MCU · BGAJ2TO DISPLAY
FIG. 01An ECG front-end board under the trace it produces: patient side, isolation barrier, system side. Only the isolated supply and the digital isolator cross the gap.
Build class
Class 3 on request
Finest BGA pitch
0.4 mm
Smallest part
0201
Components
Lot and date-code traced

01Overview

What makes a PCB fit for a medical device?

Nothing in the laminate makes a board medical. What changes is the evidence around it: the device maker must show that every unit was built the same way, from known materials, to a defined acceptance standard, and must be able to find every affected unit if something goes wrong.

So a medical build is a fine-pitch build held to a stricter discipline: a frozen drawing and stack-up, IPC Class 3 acceptance where the risk analysis calls for it, components bought only through authorised channels with their lot and date codes recorded, and no silent substitution of laminate, finish or part on a repeat order.

The quality system that governs the device is yours, usually ISO 13485, and it controls us as a supplier. We work inside it: to your approved drawing, your part list and your inspection requirements, under our own ISO 9001:2015 certified quality management system.

Last updated

02Board selection

Which boards does a medical device contain?

A patient monitor alone holds four or five constructions. The build class is chosen per board, by what that board does to the patient if it fails.
Which boards does a medical device contain?
Board in the productConstructionBase materialFinishIPC class
01Main processor board (monitor, analyser)6–8 layer multilayerFR-4, Tg 170 °CENIGClass 2 · 3
02ECG, SpO₂ and NIBP analogue front end4–6 layer multilayerFR-4ENIGClass 3 on request
03Isolated medical power supplyDouble-sided PTHFR-4, Tg 170 °CLead-free HASLClass 2 · 3
04Probe, sensor and wearable interconnectFlexible circuitPolyimide with coverlayENIGClass 2 · 3
05Pump, heater and motor control (lab analysers)Double-sided or 4 layerFR-4ENIG or lead-free HASLClass 2
06Display, keypad and touch-controller boards4 layer multilayerFR-4ENIGClass 2

IPC class belongs on each drawing, not on the product: a monitor's power board and its patient front end can justifiably sit in different classes. Class 3 adds inspection and lowers yield, so it belongs where your risk analysis puts it.

03Engineering

Where medical boards fail, and what we do about it

Medical failures are rarely dramatic. They are an intermittent joint, a leakage path that appears on humid days, or a part that quietly changed between two batches.

  • Traceability
  • Lifetime
  • Humidity
  • Signal integrity
  • Voltage
  1. P1Traceability

    A field fault has to lead back to a lot

    Job card · lot and date code

    Why boards fail

    When a device is investigated or recalled, the maker must find every unit built from the same parts and process. A supplier with no record of which lot went into which boards turns a contained problem into a product-wide one.

    How we handle it

    Every job travels on a job card through all 13 production stages, and the job number ties the boards to that record. For assemblies, lot and date-code traceability on every part. Ask for a lot or date code in the legend and we print it where your drawing shows.

  2. P2Lifetime

    Class 2 margins where Class 3 is needed

    IPC Class 3 on request

    Why boards fail

    IPC Class 2 accepts features that are fine for most products: thinner hole-wall copper, a little annular-ring breakout, minor plating voids. In equipment that must work every time it is switched on, those margins are where intermittent faults begin.

    How we handle it

    Specify IPC Class 3 and we build and inspect to it: fabrication to IPC-6012 Class 3 and assembly to IPC-A-610 Class 3. Fine-pitch work is covered too, with BGAs down to 0.4 mm pitch inspected by X-ray.

  3. P3Humidity

    Residues that conduct only when it is humid

    Requirement on the drawing

    Why boards fail

    Flux and process residues are invisible and harmless when dry. In a humid ward or a disinfected laboratory they absorb moisture and let ions migrate between closely spaced pads under bias: leakage on a high-impedance input first, a short later.

    How we handle it

    Put the cleanliness requirement on the assembly drawing: no-clean or washed flux, and any ionic limit your device file sets. We confirm at quote how the build will meet it, before anything is bought. Bare boards leave final inspection in protective packing.

  4. P4Signal integrity

    Microvolt signals beside a switching supply

    4 / 4 mil · 1–12 layers

    Why boards fail

    An ECG electrode delivers about a millivolt; an EEG signal is tens of microvolts. A front end that shares a return path with a switch-mode supply or a display backlight shows it on the trace as mains hum and baseline wander.

    How we handle it

    Give the analogue front end its own ground plane on a four- or six-layer stack-up, guard high-impedance inputs and keep the supply's switching loop small. We build 4, 6, 8, 10 and 12 layers with stack-up support, to 4 / 4 mil fine-line where the parts need it.

  5. P5Voltage

    Patient isolation must hold on every layer

    Barrier checked on every layer

    Why boards fail

    IEC 60601-1 asks for two means of patient protection between mains and the applied part: 8 mm of creepage at a 250 V working voltage. On a multilayer board a ground plane running under the isolation transformer quietly shortens the distance through insulation.

    How we handle it

    CAM checks the barrier against your drawing on every copper layer, inner layers included, before tooling. Slots under isolation parts are CNC-routed to ±0.15 mm, and the 100% electrical test proves the two sides share no net.

04Applications

Medical and laboratory equipment we build for

From bedside monitoring to the laboratory bench, prototype quantities through to scheduled production.
Flying-probe electrical tester on the S.B. Electronics production floor, used to test every net of a bare PCB
FIG. 02Flying-probe electrical test: every net on every board checked for opens and shorts before dispatch.
  • A14–8 L · ENIG

    Multiparameter patient monitors

    Processor, analogue front-end, power and display boards

  • A24–6 L

    ECG, EEG and EMG recorders

    Low-noise front ends with isolated interfaces

  • A3Flex · 4 L

    Pulse oximeters and wearables

    Compact boards with flex links to the sensor

  • A44–6 L

    Diagnostic and point-of-care analysers

    Optical, heater and pump-control boards around a processor

  • A52–4 L

    Laboratory equipment

    Centrifuges, incubators and sample handlers

  • A64 L · Class 3

    Infusion and syringe pumps

    Motor-control and alarm boards

  • A72 L

    Physiotherapy and hospital furniture

    Stimulator, motor and keypad controllers

  • Not listed?Send the drawing and a line about where the board will be used.Ask an engineer

05Specification

A starting specification for medical boards

A sound default for monitoring and diagnostic boards. Your approved drawing always wins: change any line and we quote what you specify.
Recommended starting point · medical electronics
Construction4–8 layers for processor and front-end boards; double-sided for powerRange: 1 to 12 layers
LaminateFR-4 Tg 170 °C for dense multilayers and lead-free assembly
Board thickness0.4–3.2 mm1.6 mm default; thinner for wearables
Min. track / space6 mil / 6 mil standard; 4 mil / 4 mil fine-line
Min. drill0.3 mm mechanical; 0.2 mm for fine-pitch designs
Surface finishENIG: flat, solderable pads for fine pitch and BGAAvailable: HASL · LF-HASL · ENIG · OSP
Build classIPC Class 2 by default; Class 3 on requestFabrication per IPC-6012, inspection per IPC-A-600
Flexible circuitsSingle- and double-sided polyimide flex with polyimide coverlay12.5, 25 and 50 µm polyimide film
Assembly0201 (imperial) passives; 0.4 mm minimum BGA ball pitch; QFN, QFP and fine-pitch ICsIPC-A-610 Class 2 standard; Class 3 on request
InspectionAOI at every stage; X-ray for BGA; functional test on request
ComponentsLot and date-code traceability on every partAuthorised distributors and manufacturers only — no grey-market or broker stock
Electrical test100% electrical test — flying probe or bed-of-nails fixture — plus AOI

How to order this spec

Priced online

Simple accessory and power boards (rigid single- and double-sided boards) can be priced live: 10 mm to 600 mm per side, 1 to 100,000 boards per line, dispatch in 3, 5, 7 or 10 working days.

Open the instant quote

Reviewed by an engineer

Most medical work, meaning multilayer, Class 3, flex, assembly and sourcing, is quoted by an engineer after reviewing your drawing; we aim to reply within 24 hours on working days.

Request a quote

06Traceability

From your files to dispatch, under one job number

Traceability is a chain: the files you approved, the stages the panel passed, the parts that went onto it and the boards that left. Each link is recorded against the job number, so a question about one board leads to every board built with it.

01In

What you approve

GBRFabrication data
Gerber RS-274X (or X2) plus Excellon drill files; ODB++ accepted
DWGFabrication drawing
Stack-up, IPC class, laminate, finish, and any lot or date-code marking.
BOMAssembly data
Add a BOM (CSV / Excel, with manufacturer part numbers) and centroid / pick-and-place data
QMSSupplier requirements
What your quality system asks of us: build class, marking, cleanliness and the records to return.

02Process

The traveller it moves on

TRAVELLER

Specimen · our demo board

Part / rev
SBE-DEMO-04 · rev A
Job no.
J-2611-07
Panel
2 × 2
Lot · date code
DC 2611
Build class
IPC Class 3
Layers
4
Finish
ENIG

Route · 13 stages

  1. CAM & DFM review: CAM
  2. CNC drilling: CNC
  3. Hole metallisation: PTH
  4. Dry film & imaging: DRY
  5. Copper plating: PLT
  6. Etching: ETC
  7. Automated optical inspection: AOI
  8. Solder mask: LPI
  9. Surface finish: FIN
  10. Legend printing: LEG
  11. Routing & V-scoring: RTG
  12. Electrical test: E-T
  13. Final inspection: FQC
Walk the line, stage by stage

Sign-off

  • AOI

    Passed

    10.03.26

    Every layer

  • E-T

    Passed

    12.03.26

    Every net

  • FQC

    Passed

    13.03.26

    IPC-A-600

Part lots, test log and inspection filed under J-2611-07

03Out

What leaves with the boards

LEGMarked boards
A lot or date code in the legend, wherever your drawing places it.
E-TEvery net tested
100% electrical test — flying probe or bed-of-nails fixture — plus AOI
LOTPart records
Lot and date-code traceability on every part, bought from authorised distributors only.
AOIAssembly inspection
AOI at every stage; X-ray for BGA; functional test on request
FIG. 02The record behind a medical board, drawn as a specimen traveller for SBE-DEMO-04, our own four-layer design. The route is our production sequence; the gold stages are the three gates that sign a board off.

07Standards context

Which standards govern medical electronics?

Your device is approved as a device. These are the standards it answers to, and where the circuit board enters each one.
ISO 13485
Quality management for medical device manufacturers
Your quality system. It controls us as a supplier through purchasing and supplier evaluation; we are not ISO 13485 certified ourselves.
IEC 60601-1
Basic safety and essential performance of medical electrical equipment
Means of patient and operator protection (MOPP / MOOP), creepage, clearance and leakage-current limits.
IEC 60601-1-2
Electromagnetic compatibility of medical electrical equipment
Immunity and emission tests; ground planes and stack-up are where the board helps.
IPC-6012 / IPC-A-610
Board performance and assembly acceptance, Class 2 or 3
The build class your drawing calls up; Class 3 is available on request.
Medical Devices Rules, 2017
India's device regulation, administered by CDSCO
Registration and licensing of the device sit with its manufacturer or importer.

Stays with you

Device classification, the ISO 13485 quality system, IEC 60601 testing and registration with CDSCO in India (or CE or FDA abroad) stay with the device maker. Your supplier controls, such as approved drawings, incoming inspection and audits, apply to us.

Comes from us

Boards built to your drawing and IPC class, with Class 3 on request, AOI, a 100% electrical test, final inspection to IPC-A-600, components from authorised distributors with lot and date-code records, and an ISO 9001:2015 certified quality management system.

09FAQ

Medical electronics: common questions

Not covered here? Ask an engineer — we aim to reply within 24 hours on working days.

What PCB is used in medical electronics?

Most medical devices use four- to eight-layer FR-4 boards with ENIG for processors and low-noise analogue front ends, double-sided boards for isolated power supplies, and flexible circuits for probes and wearables. Life-critical equipment usually specifies IPC Class 3; diagnostic and laboratory instruments often stay at Class 2.

Are you ISO 13485 certified?

No. We are ISO 9001:2015 certified. ISO 13485 is the device maker's quality system, and it controls us as a supplier through your approved drawings, purchasing controls and supplier audits. We build exactly to your drawing and IPC class, with job records and lot-traceable components, so the evidence your file needs exists.

Can you build medical PCBs to IPC Class 3?

Yes, on request. Class 3 tightens the acceptance criteria for hole-wall copper, annular ring, plating and workmanship, for products that must work every time. State it on the fabrication and assembly drawings; we build and inspect to it, and the quote reflects the additional inspection.

How do you trace a medical board back to its build?

Every job travels on a job card through all 13 production stages, and the job number ties the boards to that record. For assemblies we record the lot and date code of every part, bought only from authorised distributors. We can also print a lot or date code in the legend where your drawing shows.

Do you change materials or components on repeat orders?

Not without asking. Repeat orders are built to the same drawing, laminate and finish. If a laminate is discontinued or a part reaches end of life, we tell you first, propose a drop-in replacement for your approval and wait: your device file names those materials.

Who makes medical electronics PCBs in India?

S.B. Electronics manufactures and assembles PCBs for medical electronics in the G.I.D.C. Electronics Estate, Gandhinagar, Gujarat: multilayer boards up to 12 layers, flexible circuits, IPC Class 3 on request and assembly down to 0201 parts, under an ISO 9001:2015 certified quality management system. We have made circuit boards since 2000.

Medical electronics

Send the drawing, with your quality requirements.

Upload Gerbers, the fabrication and assembly drawings, the approved BOM and any supplier requirements from your quality system. An engineer reviews them and replies with a quote that states the class, laminate and tests we will build to.