Skip to content
S.B. Electronics Printed circuit boards · since 2000, home page

Resources · A–Z

PCB glossary: the terms on a board drawing, defined.

88 terms from annular ring to X-ray inspection. Each starts with a plain definition and, where it helps, a note from the factory floor on what it means for your files.
FIG. 01 · TERM INDEX88 entries
  1. A03
  2. B06
  3. C09
  4. D05
  5. E04
  6. F04
  7. G03
  8. H02
  9. I06
  10. J01
  11. K01
  12. L03
  13. M04
  14. N02
  15. O02
  16. P06
  17. R04
  18. S10
  19. T08
  20. V03
  21. W01
  22. X01
Standards: IPC · J-STD
Terms
88 defined
Covers
Fab · Assembly · Test
Standards
IPC · J-STD · RoHS
Updated
November 2026
Standards the glossary keeps pointing to
IPC-A-600What a bare board should look like: visual acceptance criteria by class
IPC-6012Qualification and performance of rigid boards: plating, annular ring, bow and twist
IPC-A-610Acceptability of soldered assemblies: joints, placement, cleanliness
J-STD-001Process requirements for soldered electrical and electronic assemblies
IPC-2221Generic design rules: spacing, track widths, hole and pad sizes
IPC-D-356Netlist format used by electrical test

A – terms beginning with A

3 terms

REF 001

Annular ring#

Annular ring is the band of copper left on a pad around a drilled hole, measured from the hole wall to the pad edge. It absorbs drill wander and layer misregistration so the hole never breaks out of the pad. IPC-6012 sets a minimum ring, stricter for Class 3 than for Class 2.

In practiceDraw the pad as the finished hole plus drill allowance plus twice the ring you want. Our design guideline is 0.15 mm minimum for drilled holes.

REF 002

Aspect ratio#

Aspect ratio is the ratio of a board's finished thickness to the diameter of its smallest drilled hole. A 1.6 mm board with a 0.2 mm hole is 8:1. High ratios make it harder for plating solution to reach the middle of the barrel, so copper there turns thin.

In practiceIf a hole must be small, use a thinner board, or enlarge the hole. Ask the fabricator for the ratio it can plate reliably.

REF 003

Automated optical inspection (AOI)#

Also: AOI

Automated optical inspection (AOI) is a camera-based check that compares a board against its CAM data or a golden sample to find defects. On bare boards it catches opens, shorts and narrow tracks on inner layers; on assemblies it checks part presence, polarity and solder joints.

In practiceAOI sees only surfaces. Joints hidden under BGAs need X-ray inspection.

B – terms beginning with B

6 terms

REF 004

Backdrill#

Also: Controlled-depth back drilling

Backdrilling removes the unused stub of a plated through-hole by drilling it out from the back with a slightly larger bit. The leftover barrel acts like an antenna and reflects multi-gigabit signals. Removing it improves signal integrity without the cost of sequential lamination.

In practiceAsk whether the fabricator supports backdrilling, and to what depth tolerance, before routing high-speed layers.

REF 005

Ball grid array (BGA)#

Also: BGA

A ball grid array (BGA) is a surface-mount package whose connections are solder balls arranged in a grid under the component body. It fits far more pins into less area than leaded packages. The joints are hidden, so the reflow profile and X-ray inspection matter more than for visible leads.

In practiceOur assembly line handles BGAs down to 0.4 mm ball pitch.

REF 006

Bill of materials (BOM)#

Also: BOM

A bill of materials (BOM) lists every component on an assembled board: reference designators, quantity, manufacturer part number, value, package and approved alternates. Sourcing and assembly teams buy and place parts from it. A BOM that disagrees with the centroid file is a frequent reason an assembly job is held.

In practiceGive manufacturer part numbers, not just values, so the right part is bought first time.

REF 007

Blind via#

A blind via is a plated hole that connects an outer layer to one or more inner layers without passing through the whole board. It saves routing space and frees surface area under dense parts. Blind vias are made by controlled-depth drilling or laser, and add lamination steps and cost.

In practiceOur multilayer range is 4 to 12 layers. Talk to an engineer before using blind or buried vias in a design.

REF 008

Bow and twist#

Bow and twist describe a board's deviation from flat. Bow is a cylindrical or spherical curve across the board; twist is one corner lifting out of the plane of the other three. IPC-6012 limits both, at 0.75 percent for surface-mount boards and 1.5 percent for other boards.

In practiceA symmetrical stack-up and balanced copper on both sides are the best defence against bow.

REF 009

Buried via#

A buried via is a plated hole that links inner layers only and cannot be seen from either outer surface. It is drilled and plated in a core before the outer layers are laminated on. Buried vias free routing space on inner layers, but every extra lamination cycle adds cost and lead time.

C – terms beginning with C

9 terms

REF 010

CAM#

Also: Computer-aided manufacturing

CAM, computer-aided manufacturing, is the engineering step where a fabricator imports your Gerber and drill data, checks it against process limits, and prepares production artwork. It adds panel borders, tooling holes, test coupons and etch compensation. Problems found here become engineering queries before any material is cut.

In practiceCAM and DFM review is the first of our production stages, ahead of drilling.

REF 011

Castellated holes#

Also: Castellations, edge plating

Castellated holes are plated half-holes along a board's edge, made by routing through a row of plated holes. They let a small module solder directly onto a carrier board like a surface-mount part. Because the plating is cut through, edge milling needs care to avoid burrs and lifted copper.

REF 012

CEM-1#

CEM-1 is a composite epoxy laminate with a paper core and woven-glass surface sheets, used for single-sided boards. It costs less than FR-4 and punches cleanly, but it cannot support reliable plated through-holes. It is common in consumer and LED boards where cost matters and one copper layer is enough.

REF 013

CEM-3#

CEM-3 is a composite epoxy laminate with woven-glass surfaces and a non-woven glass core. It looks much like FR-4, punches and drills more easily, and suits double-sided boards at lower cost. Its mechanical and thermal performance sits slightly below FR-4, so it is chosen for simple, cost-driven designs.

REF 014

Centroid file#

Also: Pick-and-place file, XY file

A centroid file, also called a pick-and-place or XY file, lists each component's reference designator, X and Y position, rotation and board side. The assembly machine's program is built from it. Origin, rotation convention and units must match the Gerber data, or every part lands in the wrong place.

In practiceSend it with the BOM for assembly quotes.

REF 015

Controlled impedance#

Controlled impedance means a track is built so its characteristic impedance, such as 50 Ω single-ended or 100 Ω differential, stays within a stated tolerance, commonly ±10 percent. It depends on track width, copper thickness, dielectric thickness and dielectric constant. Fast digital and RF signals need it to avoid reflections.

In practiceState the target impedance, reference layers and tolerance with your files. Impedance-controlled boards are quoted by an engineer, not online.

REF 016

Copper weight#

Also: Copper thickness, oz

Copper weight states copper thickness as ounces per square foot, spread evenly: 1 oz is about 35 µm and 2 oz about 70 µm. Heavier copper carries more current and spreads heat, but needs wider tracks and spacing because etching cuts deeper. Inner and outer layers can be specified separately.

In practice1 oz and 2 oz are standard; 3 oz and heavier are available on request.

REF 017

Coverlay#

Also: Coverlayer, cover film

Coverlay is the insulating film that protects the copper circuit of a flexible PCB, usually polyimide with an adhesive layer, laminated over the tracks. It does the job of solder mask but bends without cracking. Openings for pads are cut or drilled in the film before it is bonded.

REF 018

CTE#

Also: Coefficient of thermal expansion

CTE, the coefficient of thermal expansion, states how much a material grows per degree of temperature rise, in ppm/°C. Laminate, copper and components expand at different rates. A mismatch, especially through the board thickness (Z-axis), stresses plated holes and solder joints during reflow and thermal cycling.

In practiceHigher-Tg laminate expands less above its transition point, which helps thick, many-layer boards survive lead-free reflow.

D – terms beginning with D

5 terms

REF 019

Delamination#

Delamination is the separation of layers within a laminate, between prepreg and core or between copper and base material. It shows as blisters or lifted areas, often after soldering heat. Causes include trapped moisture, contamination, poor lamination pressure, or laminate with too low a decomposition temperature.

In practiceBake boards that have sat in humid storage before reflow.

REF 020

Design for manufacturability (DFM)#

Also: DFM

Design for manufacturability (DFM) is the practice of drawing a board so it can be fabricated and assembled reliably at normal yield. It covers track and space, annular ring, drill sizes, mask clearances, panel fit and component spacing. A review of your files before production catches avoidable faults while they are cheap to fix.

In practiceAn engineer reviews your Gerbers before anything is imaged.

REF 021

Dielectric#

A dielectric is the insulating material between conductors on a PCB, such as laminate cores and prepreg. Its thickness and dielectric constant (Dk) set capacitance and track impedance, while its loss tangent (Df) sets signal loss at high frequency. FR-4 has a Dk of roughly 4.2 to 4.6, depending on resin content and frequency.

REF 022

Differential pair#

A differential pair is two tracks carrying equal and opposite signals, routed together at constant spacing and equal length. The receiver reads the voltage difference, so noise picked up equally by both tracks cancels. USB, Ethernet, HDMI and LVDS use pairs, typically at 90 Ω or 100 Ω differential impedance.

REF 023

Drill file#

Also: NC drill file

A drill file lists the hole sizes and X-Y positions for every drilled hole in a board, normally in Excellon format. It separates plated from non-plated holes and often includes routed slots. The fabricator's drilling machine is programmed from it, so units and number format must be stated.

In practiceExport plated and non-plated holes as separate files, or use Gerber X2 attributes, to remove doubt.

E – terms beginning with E

4 terms

REF 024

E-test#

Also: Electrical test, bare-board test

E-test, or electrical test, checks every net on a finished bare board for opens and shorts against the netlist from your data. It uses a flying-probe tester or a bed-of-nails fixture. It is the final proof that copper is connected as designed, which visual inspection cannot confirm on inner layers.

In practiceWe electrically test every board before dispatch.

REF 025

ENIG#

Also: Electroless nickel immersion gold

ENIG, electroless nickel immersion gold, is a surface finish with a nickel layer of about 3 to 6 µm under a very thin immersion gold layer of roughly 0.05 to 0.1 µm. It gives flat pads for fine-pitch parts, long shelf life and good contact surfaces. It costs more than HASL or OSP.

In practicePoorly controlled ENIG can show black pad, a corroded nickel surface that weakens joints, so process control matters.

REF 026

Etching#

Etching removes the unprotected copper from a panel after imaging, leaving the circuit pattern. Alkaline or cupric chloride etchant dissolves the exposed copper while resist protects the tracks. Because etchant also attacks track sides, finished width is slightly less than drawn, so fabricators compensate in CAM.

REF 027

Excellon#

Excellon is the de facto standard format for CNC drill data. A file holds a tool list giving each drill's diameter, then coordinate lists for every hole each tool drills. Newer files may carry plating attributes through Gerber X2. The reader still needs to know the units and zero-suppression.

F – terms beginning with F

4 terms

REF 028

Fiducial#

A fiducial is a small copper mark, normally a 1 mm solid dot with a clear surround, that an assembly machine's camera finds to correct for board position and stretch. Global fiducials sit at panel or board corners; local ones sit beside fine-pitch parts. Two or three per side are typical.

In practiceKeep solder mask clear of the dot and the area around it.

REF 029

Flexible PCB#

Also: Flex circuit

A flexible PCB is a circuit built on polyimide film instead of rigid glass-epoxy, so it can bend, fold or flex repeatedly. Copper is laminated onto the film and protected by coverlay. It replaces wiring harnesses and connectors in tight or moving assemblies, and is often 0.1 to 0.25 mm thick.

REF 030

Flying probe#

Also: Flying-probe test

A flying-probe tester checks a bare or assembled board using two or more moving needle probes that touch pads and test points in sequence. No custom fixture is needed, so it suits prototypes and small batches. It measures continuity and isolation, though it is slower than a fixture for large volumes.

REF 031

FR-4#

FR-4 is the most common rigid PCB base material: woven glass cloth impregnated with flame-retardant epoxy resin. The FR means flame retardant, rated UL 94 V-0. Standard grades have a glass transition temperature near 130 to 140 °C, with higher-Tg grades at 150 to 170 °C and above.

In practiceWe build on FR-4 in Tg 150 °C and Tg 170 °C.

G – terms beginning with G

3 terms

REF 032

Gerber RS-274X#

Also: Gerber, RS-274X

Gerber RS-274X is the long-standing format for describing PCB layers, one file per layer: copper, mask, legend and outline. It embeds aperture definitions, unlike the older RS-274D, so no separate aperture list is needed. A set of RS-274X files plus a drill file is the usual way to send a board to fabrication.

In practiceName layers clearly and include the board outline on its own layer.

REF 033

Gerber X2#

Gerber X2 extends RS-274X with standard attributes that say what each file is, such as top copper, solder mask or plated drill, along with stack-up position and polarity. A fabricator can load a set unambiguously and ask fewer questions. It is backward compatible, so older software simply ignores the attributes.

REF 034

Gold fingers#

Also: Edge connector, card-edge contacts

Gold fingers are the plated contact strips along a board's edge that plug into a card-edge connector. They are plated with hard gold over nickel for wear resistance and bevelled so the board slides in smoothly. The gold is thicker and harder than ENIG gold, and the fingers are used on memory modules and expansion cards.

H – terms beginning with H

2 terms

REF 035

HASL#

Also: Hot air solder levelling, LF-HASL

HASL, hot air solder levelling, dips the board in molten solder and blows the excess off with hot air knives, leaving a solder coating on exposed copper. It is robust, inexpensive and easy to solder, in leaded or lead-free versions. The surface is slightly uneven, so it suits larger pads better than fine-pitch parts.

In practiceChoose lead-free HASL when RoHS compliance is required; leaded HASL is also available.

REF 036

HDI#

Also: High-density interconnect

HDI, high-density interconnect, describes boards that use microvias, thin dielectrics, fine tracks and often sequential lamination to pack more connections into less area. Microvias are typically laser-drilled and may be stacked or staggered. HDI suits fine-pitch BGAs and compact devices, at higher cost than conventional multilayers.

In practiceAsk whether a conventional multilayer will route your BGA before paying for HDI.

I – terms beginning with I

6 terms

REF 037

Impedance coupon#

Also: Test coupon

An impedance coupon is a small test structure added to the production panel's border, with tracks built to the same width, layer and dielectric as your controlled-impedance tracks. The fabricator measures it with a time-domain reflectometer to confirm impedance without destroying your board.

REF 038

IPC class#

Also: Class 1, 2, 3

IPC class is a product classification used across IPC standards. Class 1 is general electronics, Class 2 is dedicated-service electronics where continued performance is required, and Class 3 is high-reliability electronics where downtime cannot be tolerated. Higher classes demand tighter limits on plating, annular ring and workmanship, and cost more.

In practiceOur standard workmanship is Class 2; Class 3 is available on request. State the class on your drawing.

REF 039

IPC-2221#

IPC-2221, Generic Standard on Printed Board Design, is the baseline design standard. It gives rules for conductor spacing by voltage, current-carrying track widths, hole and pad sizing, and thermal and mechanical design. Companion standards such as IPC-2222 cover rigid boards in more detail.

REF 040

IPC-6012#

IPC-6012, Qualification and Performance Specification for Rigid Printed Boards, sets the measurable requirements a rigid board must meet: plating thickness, annular ring, bow and twist, solderability, cleanliness and more. It defines requirements by class, and is the contractual document behind an inspection to IPC-A-600.

REF 041

IPC-A-600#

IPC-A-600, Acceptability of Printed Boards, is the illustrated standard that shows what a bare board should look like, grading conditions as target, acceptable or defect for each class. It covers plating voids, annular ring, solder mask, marking and laminate conditions. Final inspection of a bare board is judged against it.

In practiceOur final QC is made against IPC-A-600 acceptance criteria.

REF 042

IPC-A-610#

IPC-A-610, Acceptability of Electronic Assemblies, is the visual standard for judging soldered assemblies: solder joint shape, component placement, lead protrusion, cleanliness and damage. Each condition is graded target, acceptable, process indicator or defect for Class 1, 2 or 3. It is the usual basis for inspecting assembled boards.

J – terms beginning with J

1 term

REF 043

J-STD-001#

J-STD-001 is the joint industry standard for soldered electrical and electronic assemblies. It defines process requirements for materials, methods and verification, where IPC-A-610 defines how finished joints should look. Like most IPC documents it has three classes, with Class 3 the strictest.

K – terms beginning with K

1 term

REF 044

Keep-out#

Also: Keep-out zone, keepout

A keep-out is an area on a board layer where copper, vias or components must not be placed. Typical keep-outs run along the board edge, around mounting holes, under antennas and below sensitive parts. Routed edges and V-score lines both need copper pulled back from the cut.

L – terms beginning with L

3 terms

REF 045

Lamination#

Lamination is the step that bonds etched inner cores, prepreg and outer copper foil into one solid board under heat and pressure in a vacuum press. The prepreg resin melts, flows and cures, gluing the layers. Layer registration and resin fill are controlled here, and every multilayer board passes through it.

REF 046

Legend#

Also: Component legend, nomenclature

Legend is the printed marking layer on a board, in white or another colour: component outlines, reference designators, polarity marks, logos and the revision or date code. It is also called silkscreen. It guides assembly and repair but must stay off pads, so legend is clipped where it touches exposed copper.

In practiceWhite, yellow and black legend are available.

REF 047

LPI solder mask#

Also: LPI, Liquid photoimageable

LPI, liquid photoimageable, solder mask is a liquid epoxy applied over the board, exposed to UV through the mask artwork and developed to open the pads. It is the dominant mask type because it resolves fine detail and thin dams between pads. After development it is thermally cured to full hardness.

M – terms beginning with M

4 terms

REF 048

Microsection#

Also: Cross-section, micro-section

A microsection, or cross-section, is a board sample cut, mounted in resin, ground and polished so hole plating, layer thickness and lamination can be examined under a microscope. It is destructive, so it is done on coupons or sample boards. It is the standard way to verify copper thickness in plated holes.

REF 049

Microvia#

A microvia is a very small via, typically laser-drilled, of about 0.15 mm diameter or less, connecting a layer to the adjacent one. Microvias are the basis of HDI construction. Being short, they allow dense routing under fine-pitch BGAs, and can be stacked or staggered, then filled or plated over.

REF 050

Mouse bites#

Also: Break-away tabs, tab routing

Mouse bites are rows of small drilled holes along a breakaway tab that holds a board inside a panel. The perforations weaken the tab so the board can be snapped free by hand, leaving small bumps on the edge. They are used where V-scoring is not possible, such as on boards with curved outlines.

In practiceKeep components and copper back from the tab so snapping does not damage them.

REF 051

Multilayer PCB#

A multilayer PCB has three or more copper layers, laminated together with prepreg between etched cores. Inner layers typically carry power planes and routing, and plated through-holes link them. More layers give more routing room, lower EMI and better power integrity at the cost of process steps.

In practiceWe make multilayer boards from 4 to 12 layers. Layer counts are normally even; an odd count tends to bow.

N – terms beginning with N

2 terms

REF 052

Netlist#

Also: IPC-D-356

A netlist is the list of electrical connections in a design: which pins and pads belong to each net. For fabrication, an IPC-D-356 netlist lets the electrical-test system verify that the finished board's connectivity matches the design, and comparing it against the Gerber data reveals opens or shorts the artwork introduced.

REF 053

NON-PTH#

Also: NPTH, non-plated through-hole

NON-PTH, a non-plated through-hole, is a drilled hole with no copper in the barrel. It is used for mounting screws, locating pins and clearance where an electrical connection is not wanted. Its diameter can be held tighter than a plated hole, since no plating thickness varies the size.

O – terms beginning with O

2 terms

REF 054

ODB++#

Also: ODB plus plus

ODB++ is an intelligent CAD data format that packs layers, drill, stack-up, netlist, components and fabrication notes into one structured directory. Because everything travels together, fewer files get lost or mismatched than with separate Gerber and drill files. It is common for complex multilayer boards.

In practiceWe accept ODB++ as well as Gerber.

REF 055

OSP#

Also: Organic solderability preservative, entek

OSP, organic solderability preservative, is a thin organic film over bare copper that stops oxidation until soldering, when flux removes it. It gives a flat, lead-free, low-cost finish. It has a shorter shelf life than ENIG, tolerates fewer reflow cycles, and is unsuitable for switch contacts.

P – terms beginning with P

6 terms

REF 056

Panelisation#

Also: Panelization, array

Panelisation, or panelization, arranges several copies of a board, or different boards, in one production panel with rails, tooling holes and fiducials. Boards are held by breakaway tabs or V-score lines. It makes handling by fabrication and assembly machines efficient and lets small boards be processed together.

In practiceWe panelise with V-score, tab routing or a combination.

REF 057

Pick-and-place#

Also: Component placement

Pick-and-place is the machine step in SMT assembly where a head picks components from reels or trays and places them onto solder-paste-covered pads, guided by vision and the centroid file. Placement accuracy and speed depend on the machine and part size. After placement the board travels to the reflow oven.

REF 058

Plane#

Also: Power plane, ground plane

A plane is a large continuous area of copper on a layer, usually dedicated to ground or a supply voltage. Planes give low-impedance power distribution, a return path for signals and shielding, and they spread heat. Holes through planes use thermal reliefs or clearances so they connect or isolate correctly.

REF 059

Polyimide#

Also: PI, Kapton

Polyimide is a high-temperature polymer film used as the base of flexible circuits and in high-reliability rigid boards. It stays stable above 250 °C, resists chemicals and flexes repeatedly without cracking. Kapton is its best-known brand name. It costs more than epoxy laminate and absorbs moisture.

REF 060

Prepreg#

Also: Pre-impregnated, bonding sheet

Prepreg is glass cloth impregnated with partly cured epoxy resin, the B-stage material that glues layers together in a multilayer board. Under lamination heat and pressure it flows, fills the gaps between copper features and cures hard. Its resin content and cloth style set the final dielectric thickness.

REF 061

PTH#

Also: Plated through-hole

PTH, plated through-hole, is a hole drilled through the board and plated with copper on the barrel wall to connect layers and hold component leads. Plating runs through chemical copper deposition then electroplating, normally to an average of at least 20 µm for Class 2 and 25 µm for Class 3.

R – terms beginning with R

4 terms

REF 062

Reflow soldering#

Also: Reflow

Reflow soldering melts solder paste in an oven so surface-mount components bond to their pads. The board follows a temperature profile of preheat, soak, peak and cooling. Lead-free SAC alloys peak around 240 to 250 °C. The profile must suit both the heaviest component and the most heat-sensitive one.

In practiceOur line uses an 8-zone lead-free reflow oven; leaded profiles are available on request.

REF 063

Registration#

Registration is how accurately the features on each layer line up with each other and with the drilled holes. Poor registration shrinks the annular ring and can cause breakout or shorts to inner planes. It is controlled by tooling pins, optical alignment and compensation for material shrinkage during lamination.

REF 064

RoHS#

RoHS, Restriction of Hazardous Substances, limits lead, mercury, hexavalent chromium and the flame retardants PBB and PBDE to 0.1 percent by weight in electronic products, and cadmium to 0.01 percent. It drives lead-free soldering and finishes. Four phthalates were added in later revisions.

In practiceIndia's E-Waste (Management) Rules carry comparable restrictions for listed equipment.

REF 065

Routing#

Also: Profiling, outline milling

Routing, in fabrication, is milling the board outline and internal cut-outs from a panel with a CNC router. It also separates boards from the panel, usually leaving small tabs. Outline tolerance is typically ±0.1 to 0.15 mm, and the bit's radius means internal corners cannot be perfectly square.

In practiceIn design, routing also means laying tracks. Our CNC routing tolerance is ±0.15 mm, ±0.1 mm on request.

S – terms beginning with S

10 terms

REF 066

Silkscreen#

Silkscreen is the traditional name for the legend layer: ink printed on the solder mask to label components, polarity and test points. Once printed through a screen, most is now inkjet or direct-imaged. Text about 0.15 mm in line width and 1 mm tall is a practical minimum for legibility.

REF 067

Solder bridge#

A solder bridge is unwanted solder joining two adjacent pads or pins, creating a short. It is typical of fine-pitch parts where too much paste, poor stencil release or missing mask dams let solder flow together. It is found by AOI or inspection, and removed by reworking with flux and a hot iron.

REF 068

Solder mask#

Also: Solder resist, soldermask

Solder mask is the thin polymer coating, usually green, applied over a board's copper except at pads. It insulates tracks, prevents solder bridges during assembly and protects against oxidation and contamination. Colours include green, red, blue, black, white and yellow, and thickness is typically 10 to 25 µm over copper.

In practiceWe offer green, red, blue, black, white and yellow mask.

REF 069

Solder mask dam#

Also: Mask web, mask sliver

A solder mask dam is the narrow strip of mask left between two adjacent pads, which stops solder bridging them during assembly. Fabricators need a minimum dam width, commonly around 0.1 mm, so very fine-pitch pads may be opened together with no dam at all. Check mask clearances against the fabricator's limit.

REF 070

Solder paste#

Solder paste is a mixture of tiny solder alloy spheres suspended in flux, printed through a stencil onto pads before components are placed. The paste holds parts in place until reflow melts it. Powder size is graded by type, with Type 3 common and Type 4 used for finer pitches.

REF 071

Stack-up#

Also: Layer stack, build-up

A stack-up is the ordered arrangement of copper layers and insulating dielectric in a multilayer board, with each layer's material and thickness. It sets total board thickness, impedance and mechanical balance. Agree it with your fabricator before routing, and keep it symmetrical about the centre to limit bow.

In practiceOur engineers support stack-up design for controlled-impedance boards.

REF 072

Stencil#

Also: SMT stencil, solder paste stencil

An SMT stencil is a thin stainless-steel foil with apertures cut at each pad. Solder paste is squeegeed through it to deposit exact volumes. Apertures are laser-cut, and aperture size and foil thickness decide how much paste each joint receives. Thickness is chosen for the finest-pitch part on the board.

In practiceOur laser-cut SUS304 stencils use foil from 0.08 mm to 0.2 mm.

REF 073

Stiffener#

A stiffener is a rigid piece bonded to part of a flexible circuit to support connectors or components and make insertion possible. Common materials are polyimide, FR-4 and, for heat spreading or support, aluminium or stainless steel. It is attached with adhesive and carries no circuitry.

REF 074

Surface finish#

Surface finish is the coating over exposed copper pads that prevents oxidation and keeps them solderable. Options include HASL, lead-free HASL, ENIG and OSP, each balancing cost, flatness, shelf life and contact performance. The choice is made per board and affects fine-pitch assembly.

In practiceWe offer HASL, lead-free HASL, ENIG and OSP.

REF 075

Surface-mount technology (SMT)#

Also: SMT, SMD

Surface-mount technology (SMT) is a method of assembling components that sit directly on pads on the board surface rather than in holes. Paste is printed, parts are placed by machine and the board is reflowed. SMT allows smaller packages, double-sided placement and higher speed than through-hole assembly.

T – terms beginning with T

8 terms

REF 076

Tented via#

A tented via is a via whose opening is covered by solder mask, sealing the hole on that side. Tenting keeps flux and solder out and protects the barrel from contamination and shorts. It works only for small vias, commonly up to about 0.4 mm; larger holes are plugged or left open.

REF 077

Tg#

Also: Glass transition temperature

Tg, glass transition temperature, is the temperature at which a laminate's resin softens from a rigid glassy state to a rubbery one, and its expansion rate climbs sharply. Standard FR-4 sits near 130 to 140 °C; mid and high grades are 150 °C and 170 °C. Choose a Tg above your operating and soldering temperatures.

In practiceWe build on FR-4 in Tg 150 °C and Tg 170 °C.

REF 078

Thermal relief#

Also: Thermal spoke, thermal pad connection

A thermal relief connects a pad or via to a copper plane through narrow spokes instead of a solid connection. This limits heat flow away from the joint during soldering, so the pad reaches soldering temperature and wets properly. The trade-off is slightly higher electrical and thermal resistance.

REF 079

Thermal via#

A thermal via is a plated hole placed under or near a hot component to carry heat through the board to a copper plane or the other side. Arrays of small vias beneath QFN or power-device pads are typical. Open vias can wick solder away from the joint, so they are often filled, tented or kept small.

REF 080

Through-hole#

Also: THT, through-hole technology

Through-hole technology mounts components by passing their leads through plated holes and soldering them on the opposite side. It gives strong mechanical joints, so it is used for connectors, transformers and heavy parts. Soldering is by hand, selective or wave, and it takes more board space than SMT.

REF 081

Tombstoning#

Also: Manhattan effect, drawbridging

Tombstoning is a reflow defect where one end of a small chip component, such as a resistor or capacitor, lifts off its pad and stands upright. It occurs when the paste at one end melts first and surface tension pulls the part up. Uneven pad sizes, copper imbalance and uneven heating cause it.

In practiceKeep pad sizes and attached copper symmetrical on both ends of small passives.

REF 082

Track#

Also: Trace, conductor

A track, also called a trace, is a strip of copper on a layer that carries current or signal between pads. Its width sets current capacity and impedance, and the space to the next track sets insulation. Minimum track and space are the main measure of a fabricator's fine-line capability.

In practiceWe make 6 mil / 6 mil standard and 4 mil / 4 mil fine-line.

REF 083

Turnkey assembly#

Also: Turnkey

Turnkey PCB assembly means one supplier handles everything: fabricating the boards, buying the components, assembling and testing. You send files and a BOM and receive finished boards. It contrasts with consigned or kitted assembly, where the customer supplies some or all of the parts.

In practiceWe build turnkey (we source the parts) or consigned (you supply them).

V – terms beginning with V

3 terms

REF 084

V-score#

Also: V-cut, V-groove

V-scoring cuts shallow V-shaped grooves, from top and bottom, along straight lines between boards in a panel, leaving a thin web of about a third of the thickness. Boards snap apart along the line after assembly. It lets boards sit edge to edge with no routing gap, but works only for straight cuts.

REF 085

Via#

Also: Vertical interconnect access

A via is a plated hole that connects copper on different layers and carries no component lead. Types are through, blind, buried and micro. Size is set by drill and pad diameter; smaller vias save space but are harder and costlier to make. A plated hole that holds a component lead is a PTH instead.

REF 086

Via-in-pad#

Also: VIPPO

Via-in-pad places a via directly in a component's solder pad, giving a short escape path under fine-pitch BGAs and QFNs. The via must be filled with resin or conductive paste and plated flat, otherwise solder wicks down the hole and starves the joint. It adds process steps and cost.

W – terms beginning with W

1 term

REF 087

Wave soldering#

Wave soldering passes the underside of a board over a standing wave of molten solder, which wets exposed pads and leads and forms through-hole joints in one pass. Surface-mount parts on the underside need adhesive or a pallet. It suits volume through-hole builds; selective soldering handles mixed boards.

In practiceOur assembly line offers reflow, wave and selective or hand soldering.

X – terms beginning with X

1 term

REF 088

X-ray inspection#

Also: AXI

X-ray inspection images inside a finished assembly or board without cutting it. It reveals hidden solder joints under BGAs and QFNs, voids, bridging and barrel plating condition, with denser areas appearing darker. It is used for process checks and first-article inspection where AOI cannot see.

In practiceWe use X-ray for BGA inspection.

FAQQuestions

Questions engineers ask about these terms.

The terms that most often cause a query on a first order, answered in a few lines.

What is the difference between IPC-A-600 and IPC-6012?

IPC-A-600 is the illustrated acceptability guide for bare boards, showing target, acceptable and defect conditions. IPC-6012 is the performance specification that sets measurable requirements such as plating thickness, annular ring, bow and twist. A rigid board is built to IPC-6012 and judged visually against IPC-A-600.

Which surface finish should I choose: HASL, ENIG or OSP?

HASL suits low cost and larger pads. ENIG gives flat pads for fine-pitch parts, a long shelf life and good contact surfaces. OSP is a flat, lead-free, low-cost finish for boards assembled soon after fabrication. Tell us the finest-pitch part on your board and we will recommend one.

Which design files do I need to send for fabrication?

Send Gerber RS-274X or X2 files, one per layer including the board outline, plus Excellon drill files; ODB++ is also accepted. For assembly, add a BOM with manufacturer part numbers and a centroid file. Zip everything into one archive and upload it with your quote.

What Tg should my PCB laminate have?

Tg 150 °C is a sound default for many boards. Choose Tg 170 °C for thicker multilayers, repeated lead-free reflow or products that run hot. Whatever the grade, keep the Tg comfortably above your peak operating temperature, and remember standard FR-4 sits lower, near 130 to 140 °C.

What is the difference between a via and a PTH?

Both are plated holes. A via only connects copper on different layers and carries no component lead. A PTH, a plated through-hole, is sized to take a component lead and solder it in place, as well as linking layers. Vias can also be blind, buried or micro; a PTH goes through the whole board.

Still unsure of a term?

Send the drawing. An engineer will read it with you.

Upload your Gerbers or ask a question about any term on your drawing. We review files before anything is imaged, and reply with a reviewed quote.