Skip to content
S.B. Electronics Printed circuit boards · since 2000, home page

Engineering guide · Assembly & standards

IPC Class 2 vs Class 3 — which does your board need?

What the three classes mean, which acceptance criteria tighten from Class 2 to Class 3, and how to specify reliability only where a failure would really cost you.
Soldering iron tip at a fine-pitch QFP on a green PCB during inspection and rework
FIG. 01Soldering iron tip at a fine-pitch QFP on a green PCB during inspection and rework
Written by
S.B. Electronics Engineering Team
Published
Updated
Reading time
7 min · 1,507 words
On this page · 9 sections
  1. 01What are IPC Class 1, 2 and 3?
  2. 02What actually changes between Class 2 and Class 3?
  3. 03Why does Class 3 cost more?
  4. 04Which IPC class does your board need?
  5. 05Does the class apply to the bare board, the assembly or both?
  6. 06How is compliance with a class verified?
  7. 07Can one board mix Class 2 and Class 3 requirements?
  8. 08How do you specify the class on an order?
  9. 09What does S.B. Electronics build to?

Building this board?

IPC classes define how strictly a printed circuit board and its assembly are inspected and accepted. The same Gerber data can be built to Class 2 or Class 3; what changes is the acceptance criteria applied to the finished product — and with them the process margin, inspection effort and cost needed to meet them. Choosing a class is really a decision about what a field failure would cost you.

What are IPC Class 1, 2 and 3?

IPC uses the same three performance classes across its main standards: IPC-6012 (qualification and performance of rigid boards), IPC-A-600 (visual acceptability of bare boards), IPC-A-610 (acceptability of assemblies) and J-STD-001 (soldering requirements). The class goes on the purchase order or fab drawing, and every inspector along the line works to it.

Table 1 · The three IPC performance classes

ClassDefinitionTypical products
Class 1 — GeneralThe completed product must function; cosmetic defects are acceptableToys, low-cost disposable consumer items
Class 2 — Dedicated serviceExtended life and continued performance; uninterrupted service desired but not criticalIndustrial controls, power supplies, meters, telecom, appliances, most commercial products
Class 3 — High reliabilityContinued performance, or performance on demand, is critical; downtime cannot be toleratedLife-support and safety-critical systems, harsh-environment controls, aerospace

Class 1 is rarely specified for professional work. For almost every customer we speak to, the real decision is Class 2 versus Class 3.

What actually changes between Class 2 and Class 3?

The differences are in tolerances and in evidence. Class 3 leaves less room for drill wander, thin plating and imperfect solder joints, and asks for more proof — microsections, test coupons, inspection records — that the build meets them. The figures below are the commonly quoted values; exact limits depend on the revision your drawing calls out, so always check the current edition of the standard.

Table 2 · Key acceptance criteria, Class 2 against Class 3

CriterionClass 2Class 3Standard
External annular ring, plated holesUp to 90° breakout permittedNo breakout; 50 µm minimum ringIPC-6012
Hole-wall copper, average20 µm (18 µm minimum in thin spots)25 µm (20 µm minimum in thin spots)IPC-6012
Vertical solder fill, plated through-hole75%; 50% accepted in defined cases75%IPC-A-610 / J-STD-001
Chip component side overhangUp to 50% of termination widthUp to 25% of termination widthIPC-A-610
Chip component end-joint widthAt least 50% of termination widthAt least 75% of termination widthIPC-A-610
Bow and twist, boards with SMT parts0.75% maximum0.75% maximumIPC-6012

Typical values from the current revisions; your drawing's called-out revision governs. Scroll the table sideways →

Fig. 02Annular ring · breakout by class

01Class 1

Up to 180° breakout: the hole may sit on the pad edge.

02Class 2

Up to 90° breakout permitted on plated holes.

03Class 3

No breakout; at least 50 µm of ring all round.

Annular ring at the three classes: Class 1 tolerates 180° breakout, Class 2 up to 90°, Class 3 none — the drilled hole must stay inside the pad with a 50 µm ring all round.

Note the last row: not everything tightens. Flatness limits are the same for both classes, because they are set by assembly needs rather than by reliability. The pattern is that Class 3 tightens anything that affects how long a joint or a plated barrel survives.

Why does Class 3 cost more?

Class 3 cost comes from margin and evidence, not from different machines. To guarantee no annular-ring breakout, the design needs larger pads or the process needs tighter drill registration. To guarantee 25 µm average hole-wall copper, plating runs longer and surface copper grows with it, which pushes etch compensation on fine lines. Each lot needs microsection evidence from test coupons, and inspection takes longer at higher magnification. Assemblies need tighter placement, and every joint is judged against stricter fillet criteria. Yields fall as acceptance windows narrow, and scrapped panels are part of the price.

Class 3 adds time as well as cost. Microsection coupons must be cut, polished and read before a lot is released; more boards are inspected at higher magnification; and a lot that fails a coupon check is rebuilt rather than reworked. Plan for it in the schedule. If time matters more than the class for a first prototype, build the prototype to Class 2 and the qualification lot to Class 3.

What does the extra plating buy?

Thicker barrel copper survives more thermal cycles. Every reflow pass and every field temperature swing expands the laminate in its thickness: standard FR-4 grows roughly 50–70 ppm/°C below its glass transition temperature and several times faster above it. The copper barrel has to stretch with it, and a thicker barrel cracks later. That is also why Class 3 builds tend to call for higher-Tg laminate — lower Z-axis expansion and more margin through lead-free reflow.

Which IPC class does your board need?

Ask one question: what happens if this board fails in the field? If the answer is a service call, a replaced unit or an unhappy customer, Class 2 is the industry norm and the right economic choice. It is not a low-quality tier — it is the class most industrial and commercial electronics is built to. If the answer involves patient safety, vehicle safety, a mission that cannot be repeated or equipment nobody can reach, specify Class 3 and budget the cost and time.

Table 3 · Usual choices by product type

ProductUsual classWhy
Consumer and IoT devicesClass 2Cost-driven; a failure is inconvenient, not dangerous
LED drivers and lightingClass 2Long life matters, but a failure means a replaced lamp
Industrial controls, drives, metersClass 2Extended service; Class 3 for safety functions if the design calls for it
Telecom and networkingClass 2Continuous service, usually with redundancy at system level
Life-support, aerospace, safety systemsClass 3Failure cannot be tolerated

Industry practice is a guide, not a rule. Your product standard, your customer's specification or your own risk analysis decides.

Does the class apply to the bare board, the assembly or both?

The class is specified separately for the bare board and for the assembly, and the two do not have to match. One combination worth considering is an IPC-6012 Class 3 bare board — thick barrel copper, no breakout — assembled to IPC-A-610 Class 2, because over a long service life the plated holes are often the bigger reliability risk. The reverse rarely makes sense: Class 3 solder joints on a Class 2 board still leave the barrels as the weak point. Decide each class on its own merits and write both down.

How is compliance with a class verified?

A class is only as good as the evidence behind it. For bare boards the key check is the microsection: a test coupon cut from the production panel is potted, polished and examined under a microscope to measure hole-wall copper, annular ring, plating voids and dielectric thickness. The other common checks:

  • Electrical test — every net checked for opens and shorts, at every class.
  • Thermal stress — a coupon floated on 288 °C solder for 10 seconds (IPC-TM-650 2.6.8), then microsectioned to look for cracks and separation.
  • Solderability — sample pads tested to J-STD-003 to confirm the finish wets properly.
  • Ionic cleanliness — residues measured on the board, important for high-impedance and high-voltage circuits.
  • Bow and twist — measured on a surface plate per IPC-TM-650 2.4.22.

At Class 2 much of this is done by sampling. At Class 3 the evidence is typically required for every lot, which is part of what the extra cost pays for.

Can one board mix Class 2 and Class 3 requirements?

Yes, and it is often the smartest specification. A product can be built to Class 2 overall with named Class 3 requirements where they matter — Class 3 annular ring on a connector that sees vibration, or Class 3 hole-wall copper on a board that sees many thermal cycles. Write the exceptions on the fab drawing, for example 'IPC-6012 Class 2, except hole-wall copper per Class 3', rather than upgrading the whole board. You pay for reliability only where it earns its keep.

How do you specify the class on an order?

  1. Name the bare-board standard and class on the fab drawing — for example, 'IPC-6012 Class 2, acceptance to IPC-A-600 Class 2'.
  2. Name the assembly standard separately — 'IPC-A-610 Class 2' or 'J-STD-001 Class 3' — on the assembly drawing or purchase order.
  3. List any extras: microsection reports, impedance coupons, cleanliness testing.
  4. Check that the design supports the class: pad sizes that allow no breakout, drill-to-copper clearances, and a stack-up that tolerates the plating you ask for.
  5. Never rely on a default for a safety-critical product. If nothing is stated, most fabricators build to Class 2.

What does S.B. Electronics build to?

We fabricate bare boards to IPC-6012 and inspect them against IPC-A-600 acceptance criteria at final QC. Assemblies are built to IPC-A-610 Class 2 standard; Class 3 on request. For regulated sectors we build to IPC Class 3 and your drawing; your product's sector certification stays with you. Our quality system is ISO 9001:2015 certified — see quality and testing for how inspection and electrical test work on our floor.

Written by

S.B. Electronics Engineering Team

The CAM, production and quality engineers at our factory in the Gandhinagar G.I.D.C. Electronics Estate — the people who review incoming data and build the boards. Published ; last reviewed and updated .

Ask the engineering team a question

Questions

Questions about IPC classes

Short answers to what engineers ask us most often about this subject.

Is IPC Class 2 good enough for industrial products?

Yes. Class 2 is the standard for dedicated-service electronics: industrial controls, power supplies, meters, telecom and most commercial products. It assumes extended life and continued performance. Move to Class 3 only where a failure would be dangerous or unrecoverable, or where your customer's specification requires it.

Does Class 3 change my PCB design?

It can. With no annular-ring breakout allowed, pads must be large enough to absorb drill and registration tolerances. Thicker hole-wall copper affects fine-line etching, and stricter assembly criteria favour generous land patterns. Decide the class before layout, not after, so the design has the margin the class needs.

What is the difference between IPC-6012 and IPC-A-610?

IPC-6012 sets performance and qualification requirements for the bare rigid board: plating, annular ring, dielectric and bow and twist. IPC-A-610 sets visual acceptance criteria for the assembled board: solder joints, component placement and cleanliness. A typical order calls out both, each with its own class.

How much more does an IPC Class 3 board cost?

It depends on the design rather than a fixed surcharge. A board with generous pads and standard features may cost a little more; a dense board where Class 3 pushes tolerances costs considerably more, because yields fall and inspection lengthens. Send your data and ask for both classes to see the difference.

Which IPC standards does S.B. Electronics build to?

Bare boards are built to IPC-6012 and inspected against IPC-A-600. Assemblies are built to IPC-A-610 Class 2 standard; Class 3 on request. Our quality system is ISO 9001:2015 certified; any sector certification for your product, such as a medical or automotive approval, stays with you.

Start a project

Send the data. We will check it before we build it.

Price one- and two-layer boards online in seconds, or send the full data pack — Gerbers, drill, fab note, BOM and centroid — and an engineer replies with a reviewed quote.